Jump to content
SAU Community

1jz-gte Tt Engine For Sale


Recommended Posts

Well I thought I might as well start a seperate thread from the one with the details of my written off Soarer to sell the engine. The transmission is now sold, and previously I was asking 2k for the engine + transmission but due to my financial circumstances I am selling the engine itself for $1000. Offers are welcome as the engine is in storage and is costing me way too much. I'd let it go for pretty much....anything (as much as I dont want to admit it lol).

:D

The turbos were re-built approximately 6 months ago, but since I only owned the car for 6 weeks, I don't know if they are steel-wheeled or ceramic...so the buyer could get a nice little bargain if they are steel. Pretty much this just needs to go, its got 129,xxxk's on it, and was running fine when i had the car, no problems at all. It was even running still nicely after the accident!

The engine is currently in Croydon, VIC 3136

Contact: Ash

[email protected]

0400531138

Inspections and that are welcome, note: I don't have the facilities to get it on a trailer for you, so a crane might be needed...or a few mates :bunny:

Heres Pics:

14072007111-small.jpg

14072007108-small.jpg

Link to comment
Share on other sites

nah dont have the loom. And sending interstate is too much of a hassle at this point in time, considering theres a few people around the area interested in it. If it doesnt go in a few weeks then maybe....but i plan to have it gone by next weekend.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Great info @tidi0x  Will definitely be handy for others and maybe me if I decide to keep the shit box H pattern.
    • Bumping this up one last time.... I wanted to follow up on the clutch slave issue. I realized that what the issue comes down to is the pocket is flat milled, and the cylinder does not want rest flat. So in order to mount it correctly you will need to make a spacer for the fingers so the cylinder is floating. I took two plates of aluminum, drilled some holes and was good. I did still need to make the relief cuts in the bell housing, as even with the spacer the bleed section still interferes. The OE bell housing the mounting holes are raised from the housing.       
    • If the event in USA goes ahead will be interesting as it seems the rules will get more cars over here. Apparently the track is laguna seca too. Yeah s15, if I get a the lower dash trims, centre console and change front cross member to standard LCA position will fit clubsprint. See how rules are as i would rather do complete widebody than a bolt on flare to run the 295 with proper clearance.
    • If the car is legal height I can't see it being an issue. Found a thread on reddit that might offer some insight.   I got a ticket from a copper in QLD for my S15 being too low. They had this wheel thing on a stick that they put under the car and it hit my exhaust. Anyhow went to an exhaust shop to get the exhaust tucked up/hung a little higher and I wound the coilovers up a smidge. Don't think I even had to go back to the police station unlike when I got defected for having a carbon bonnet when I brought the S15 from the ACT to QLD and had to replace it and then rock up at a police station and have a yougish female officer who knew nothing about cars confirm that I had changed bonnets. Should have just painted the carbon bonnet yellow to match the rest of the car lol
    • Id like to race in the US i think alot of those track would suit me   For the s15? Youd be stuck between club sprint and the new Open Am wouldnt you depending on how much interior you have left in
×
×
  • Create New...