Jump to content
SAU Community

Recommended Posts

Garrett GT 2510 Ball Bearing turbo

In South Australia, Adelaide.. but can post anywhere

Excellent Condition . no shaft play.will suit rb20det or sr20det i have the adaptor plate to switch from an sr manifold to T3 flange.. Has gaskets and lines included. the actuator is included just not shown on the turbo..never been on my car, but i brought it with my car!! i'm now goin a bigger turbo so do not require this one. this turbo is very very responsive being ball bearing.. capable of making around 240kw, with sum minor mods

ADDED...

Just found out that this will suit a ca18 too.. as it is a t25 flange.. but if u want it for a 32 i can giv u the adaptor plate too.. will work great on any of these combos.. R32 rb20det.. SR20det.. or CA18det.. very quick spooler, ball bearing turbo great condition.. can take upto 22-23 psi

Price Drop to $900 price now includes dump.. and downpipe :D

Ph- 0408 820 538

image005rl7.jpg

image006yo6.jpg

image007wm0.jpg

image008yc9.jpg

image009ul6.jpg

Cheers Chris[/size]

Edited by super_32
Link to comment
Share on other sites

hey mate where you located? how many km's if you know? also do you know if the dump pipe design is same as std skyline?

Im located in South Australia, Adelaide

Sorry should have mentioned that its a 3inch dump pipe..the story i was told is that the turbo is from an sr thats why the adaptor plate is there to suit a rb manifold and i believe that the dump is a straight bolt to the turbo.. hope thats some help

Unsure of the Kms on turbo.. but had it checked over by Turbo Tune here in S.A.. checks out fine.. no shaft play

chris

Link to comment
Share on other sites

thanks man.. there hasnt been too much interest.. so i hope this price does get it out of my garage ;)

Hopefully man, bargain at that price!

Good luck with selling it, people are missing out bad to pass it up at this price.

Unfortunately I have to pay for compliance before I can go spending 900 on a turbo!..

But if things change I will let you know.

Thanks,

Abu

Link to comment
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Latest Posts

    • Well unfortunately after reviewing B-52 of the stagea manual and doing the following checks, it looks like it might be an ECU issue: Pins 25, 32, 116 and 124 have good earths (interestingly 10 and 19 don't have pins in the plug although the diagram says they should be earths Pins 80 and 109 have good battery voltage ECCS relay pins 1 and 3 have good battery voltage, and if I earth pin 2 (normally the ECU earth trigger to turn ECCS on) the relay activates and I get battery voltage at pins 67 and 72 as well. Also, when I plugged the old powerFC in it showed battery voltage on the hand controller, and started and ran the engine (poorly, since the AFM is no longer connected!) So, based on all that I'm thinking it is an internal issue in the ECU, I've contacted Link to see what they say
    • Should’ve been thinking about your mates while taking shits. Unacceptable.
    • I’ll take the side skirts, rear bumper, and wing off you hands if it’s still available
    • Yeah the whole car, past roof totally out of sight. The old owner said the roof lining didn’t need cleaning because there was a air pocket trapped haha. it doesn’t matter I’m not going to quit, I’m going to put number plates back on this sub haha I guess I’m getting gaskets for the intake manifold because it’s coming off,injectors out for a little look see next.
    • ER34 GTT Altia  I want to have such setup:  18x8.5 ET35 - 235/40R18  18x9.5 ET22 - 265/35R18 I have no worry for front.  I'm confused about ET22 rear. Is anyone ride on 265 at rear with ET22 or less, I don't want to roll the guards. 
×
×
  • Create New...