Jump to content
SAU Community

Sold

super_32
 Share

Recommended Posts

super_32 Enthusiast

super_32

Posted
Posted (edited)

Garrett GT 2510 Ball Bearing turbo

In South Australia, Adelaide.. but can post anywhere

Excellent Condition . no shaft play.will suit rb20det or sr20det i have the adaptor plate to switch from an sr manifold to T3 flange.. Has gaskets and lines included. the actuator is included just not shown on the turbo..never been on my car, but i brought it with my car!! i'm now goin a bigger turbo so do not require this one. this turbo is very very responsive being ball bearing.. capable of making around 240kw, with sum minor mods

ADDED...

Just found out that this will suit a ca18 too.. as it is a t25 flange.. but if u want it for a 32 i can giv u the adaptor plate too.. will work great on any of these combos.. R32 rb20det.. SR20det.. or CA18det.. very quick spooler, ball bearing turbo great condition.. can take upto 22-23 psi

Price Drop to $900 price now includes dump.. and downpipe :D

Ph- 0408 820 538

image005rl7.jpg

image006yo6.jpg

image007wm0.jpg

image008yc9.jpg

image009ul6.jpg

Cheers Chris[/size]

Edited by super_32
Link to comment
Share on other sites
super_32 Enthusiast

super_32

Posted
  • Author
Posted
hey mate where you located? how many km's if you know? also do you know if the dump pipe design is same as std skyline?

Im located in South Australia, Adelaide

Sorry should have mentioned that its a 3inch dump pipe..the story i was told is that the turbo is from an sr thats why the adaptor plate is there to suit a rb manifold and i believe that the dump is a straight bolt to the turbo.. hope thats some help

Unsure of the Kms on turbo.. but had it checked over by Turbo Tune here in S.A.. checks out fine.. no shaft play

chris

Link to comment
Share on other sites
abu Grand Master

abu

Posted
Posted
thanks man.. there hasnt been too much interest.. so i hope this price does get it out of my garage ;)

Hopefully man, bargain at that price!

Good luck with selling it, people are missing out bad to pass it up at this price.

Unfortunately I have to pay for compliance before I can go spending 900 on a turbo!..

But if things change I will let you know.

Thanks,

Abu

Link to comment
Share on other sites
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      Haltech Iat Vs. Oem Iat Rb26 ?

      By GTSBoy · Posted

      It's not going to differ from the T measured at the cast pipe by more than 0.5°C, under any conditions where it matters. Not sure, but it's either in the floor or the side, in the main body of the plenum.
    • soviet_merlin
      Haltech Iat Vs. Oem Iat Rb26 ?

      By soviet_merlin · Posted

      Where does Plazmaman place the bung for the IAT sensor? They supply the big hp kits so I would expect them to have given it some consideration.
    • soviet_merlin
      Haltech Iat Vs. Oem Iat Rb26 ?

      By soviet_merlin · Posted

      Going from your photo you may just have the Blitz intercooler core but not the piping. Maybe the previous owner didn't like the 2000s Autosalon chrome look. I certainly don't like it This is what the Blitz plumbing looks like on the Stagea. The sensor sits pretty far from the plenum. No idea if it makes a difference. The piping itself is pretty tidy IMO as they route it through the factory sidemount intercooler holes in the engine bay.
    • WMDC35
      R32 Rear Seats

      By WMDC35 · Posted

      Seatbelt bolts are 7/16 UNF in most cases
    • Kinkstaah
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Kinkstaah · Posted

      Yes, this is why I end up being 'vocal' with executives. "I want it" can't be "Just because we should have it" you need reasons. It has way too big knock on effects to simply want something "Just because" at that level in orgs with 10,000+ employees. Currently, message labelling. Sounds great. Except there is no governance on how to actually HANDLE message labels, so I may as well implement the labels as "Pink Flamingo" or "Conrod" or "Massive Dildo" and force people to choose one for every message, with no framework underpinning any of it. It has no value and can actually have detrimental value if all it does is serve to annoy people into clicking something random, or just using the default for everything, especially if there's no repercussions for getting it wrong, no monitoring for people doing it right, and no guidance on what needs to be what label. "But we need message labels!" f**k sake.
×
×
  • Create New...