Jump to content
SAU Community

Recommended Posts

Hey guys,

Just looking for a bit of input here. Ive got an advanced driving course coming up, and i can remember from my last one, there was a lot of running over cones. Now that was fine in the old 31, but the new arrival 32 sits a bit lower... Im a bit worried ill be driving home with a mangled front bar after the days out. Am i being over cautious?

Cheers in advance,

Nasha

Link to comment
https://www.sau.com.au/forums/topic/179333-front-bar-witches-hats-bad/
Share on other sites

Just throw on your standard front bar if you don't already have it on. Go out have some fun and just throw your aftermarket bar back on. If you've only got a standard front bar, go out damage it and now you have an excuse to get an aftermarket one. :nyaanyaa:

Or just don't hit the cones in the first place.

if it is the stock plastic one it should be fine unless you are hitting them at 150km/h. if it is an aftermarket bar then you may want to change it. i took my fibreglass bar in a few motorkanas and it survived ok, but i didn't really hit any cones. what did damage it though was when i let a mates missus drive it and she went off the side of the skidpan and through some deep mud, but that only put a few inch long cracks in it..... but then i did add a heap more glass to it to make it stronger before i put it on. some of the cheap crappy ones out there i'm suprised don't crack just by driving down the highway at 100kmh.

Harden up? I dont have $700 to replace the bar if it breaks, its not original, and i dont have the original unfortunately.

Why a 2nd, because with John Bowe Driving School theres 3 stages of advanced driving, then the CAMS certification day!

Why hitting cones, because the last course had emergency braking and swerving in the wet from 80km/h, dont swerve enough, or too much or lockup the breaks and your likely to hit some cones too.

Clearly some attitude problems with people in this forum...

I'd rather leave the bar on then take it off. When you take it off, you're letting the cooler (if you've got a front mounted one installed) get all the damaged. Just go out to a wrecker and pick up a stock bar. Better than spending $700 ( :P ) on a new one.

I'd rather leave the bar on then take it off. When you take it off, you're letting the cooler (if you've got a front mounted one installed) get all the damaged. Just go out to a wrecker and pick up a stock bar. Better than spending $700 ( :P ) on a new one.

i got a 31 so not too fused about hitting stuff.

but year have a look on the for sale parts there should be a few bars that you could buy cheep.

I hit a cone at about 90kphish. All it did was crack the paint a little bit. Nothing a quick coat of paint wont fix. Just get out there and have some fun. Maybe spend more time concentrating on the course, and less time worrying about what will happen "if" you hit cones and you may actually miss them :P

Have fun and good luck!!!

Remember, each cone you hit, is something like a dog/cat/person/telegraph pole.

It'll do more then chip the paint in real life... :(

Also, the skid pan day I did, I didn't see a SINGLE piece of damage to a car, even the onet hat dragged the cone under it at 80km/h for aorund 150metres...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When's the rear mounted turbo kit coming? Needs dose and V8 chop idle lol.
    • I was very unimpressed with how the car came up from the A pillar forward, before I hit things (twice). It all has to go. It had to go, but now it has to go... more. So we finally found the very first Shennanigans with the entirely perfectly setup engine that had no problems being pulled apart to improve on 'was perfectly fine'. Cam bearings looked a bit... stock. Which isn't entirely bad given they were stock and this is a ~20 year old engine. So new cam bearings are on the way because it's somewhat difficult to get to this stage to do it later, and it will trash the block. It was quite unusual that it wasn't done when the perfectly new-looking VCM cam was originally installed by [unknown] What IS unusual is the cam that was installed there was advanced SIX degrees. As to why there is no way to know.. however it could have been @Dose Pipe Sutututu's mate who wanted a larger cam sound but also wanted it to come on earlier to be more usable. This is my dyno sheet with the previous setup - This cam is not supposed to peak until 7000+ RPM, according to VCM. This is what lead me down the whole 'my heads/intake setup is running out of puff and can't support the cam' line of thinking to begin with. Anyway too late now - New cam is in! It could be rather funny if this smaller cam acts like a larger cam because it isn't advanced six degrees. In the spirit of everything is working amazingly - the COMP cam required no dialling in whatsoever. It was about 0.5 degrees advanced, which seems pretty bang on. Any adjustment either way would be further out. I'm told as a chain breaks in it ends up regarding back about 0.5 a degree as the chain breaks in, making it bang on. In the spirit of everything was previously working amazingly - The timing gear that was taken out turned out to be was an N-Motion double timing chain kit, with adjustable cam gear (which is how it was 6 degrees advanced) and all looks entirely perfectly new. It also had a Torrington bearing, which was one of the reasons I ended up getting the Cloyes kit which they used in the C5R 24 hour racecar - Because I couldn't confirm what was in the engine when talking to Tony Mamo. I did believe however it was a Double chain kit of some kind... but found no supporting documentation or evidence for it.
    • I recently did this to my R33 with the full set from Car Mats Direct, they can't do the vinyl anymore that's advertised on the website due to a supplier issue so I ended up with the Black Loop Pile which looks great. I went all out with rubber sound deadening sheets from Repco and also added the sound deadening foam layer option with the carpet. Makes a world of difference and got rid of all the weird smells in the 29 year old interior. It was a bit of work but I'd 100% recommend it, Car Mats Direct had awesome customer service and quick postage. Replaced my seats with some sporty ones from Autotechnia while I was at it, feels like a new car.
    • Got the motor out and torn down. I'll be dropping off the block Monday. Luckily the scoring on Cyl6 is much less pronounced then the pictures made it out to seem. It can barely be felt. If you pass your finger over it 10x you'll barely notice it. Hopefully by some chance it will only require a honing. I'm not in the mood to buy one size larger pistons or another block. Oddly enough my 6th cylinder with the scoring has extremely clean intake valves compared to my other 5 cylinders. I'm worried the scoring was caused by too much fuel or Water/Methanol washing the cylinder. I'll review some old logs to confirm.  This was also the first time I pull an engine with the transmission still attached. It went much better then expected. I was worried my CD009 wouldn't make it easy due to its sheer size but it was much easier this way. 
×
×
  • Create New...