Jump to content
SAU Community

Recommended Posts

Hey guys,

Just looking for a bit of input here. Ive got an advanced driving course coming up, and i can remember from my last one, there was a lot of running over cones. Now that was fine in the old 31, but the new arrival 32 sits a bit lower... Im a bit worried ill be driving home with a mangled front bar after the days out. Am i being over cautious?

Cheers in advance,

Nasha

Link to comment
https://www.sau.com.au/forums/topic/179333-front-bar-witches-hats-bad/
Share on other sites

Just throw on your standard front bar if you don't already have it on. Go out have some fun and just throw your aftermarket bar back on. If you've only got a standard front bar, go out damage it and now you have an excuse to get an aftermarket one. :nyaanyaa:

Or just don't hit the cones in the first place.

if it is the stock plastic one it should be fine unless you are hitting them at 150km/h. if it is an aftermarket bar then you may want to change it. i took my fibreglass bar in a few motorkanas and it survived ok, but i didn't really hit any cones. what did damage it though was when i let a mates missus drive it and she went off the side of the skidpan and through some deep mud, but that only put a few inch long cracks in it..... but then i did add a heap more glass to it to make it stronger before i put it on. some of the cheap crappy ones out there i'm suprised don't crack just by driving down the highway at 100kmh.

Harden up? I dont have $700 to replace the bar if it breaks, its not original, and i dont have the original unfortunately.

Why a 2nd, because with John Bowe Driving School theres 3 stages of advanced driving, then the CAMS certification day!

Why hitting cones, because the last course had emergency braking and swerving in the wet from 80km/h, dont swerve enough, or too much or lockup the breaks and your likely to hit some cones too.

Clearly some attitude problems with people in this forum...

I'd rather leave the bar on then take it off. When you take it off, you're letting the cooler (if you've got a front mounted one installed) get all the damaged. Just go out to a wrecker and pick up a stock bar. Better than spending $700 ( :P ) on a new one.

I'd rather leave the bar on then take it off. When you take it off, you're letting the cooler (if you've got a front mounted one installed) get all the damaged. Just go out to a wrecker and pick up a stock bar. Better than spending $700 ( :P ) on a new one.

i got a 31 so not too fused about hitting stuff.

but year have a look on the for sale parts there should be a few bars that you could buy cheep.

I hit a cone at about 90kphish. All it did was crack the paint a little bit. Nothing a quick coat of paint wont fix. Just get out there and have some fun. Maybe spend more time concentrating on the course, and less time worrying about what will happen "if" you hit cones and you may actually miss them :P

Have fun and good luck!!!

Remember, each cone you hit, is something like a dog/cat/person/telegraph pole.

It'll do more then chip the paint in real life... :(

Also, the skid pan day I did, I didn't see a SINGLE piece of damage to a car, even the onet hat dragged the cone under it at 80km/h for aorund 150metres...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...