'jun Style' Copy Intake Plenum For Rb25

[jonnob55]

http://cgi.ebay.com.au/R32-R33-R34-RB25DET...1QQcmdZViewItem

Hey guys, Ive done a bit of searching through different forums including this one and cant really find any info on these plenums. They appear to be good quality, have velocity stacks inside the chamber and are nowhere as cheap as greddy copies!

Just wondering if anyone has used one of these on their rb25, wat the quality is like, performance, etc. Currently deciding whether or not to buy a genuine greddy plenum or one of these as i can purchase with a 90mm throttle body for 1g. Thanks for any input you can provide!

[teazn_r33]

this was covered on the greddy copy thread they are not as good as they look id go ahead with the greddy for that tiny bit extra i have a greddy copy and it is good but i suggest you not go for one of these

[jonnob55]

Thanks teazn r33, i know they were briefly covered but i couldnt really find anyone who actually had one on their car.

Thanks for your advice though!

[silver gts-t]

this was covered on the greddy copy thread they are not as good as they look id go ahead with the greddy for that tiny bit extra i have a greddy copy and it is good but i suggest you not go for one of these

they dont look anywhere near as bad as the greddy style ones, ive been contemplating..

if u look at the rb20 ones u will see its the plenum with standard runners welded on, suppose u have to remember the postage is another $175 on top.

Edited August 6, 2007 by silver gts-t

[Bliksem]

pretty sure those JUN copies are made in Thailand or Taiwan... cant remember...

Greenline sell the genuine Greddy ones for $885 so just go with that. Atleast its a proven Japanese brand and you will be supporting the company who has ACTUALLY come up with the design and done the research and development...

[700HP-GTR33]

they dont look anywhere near as bad as the greddy style ones, ive been contemplating..

if u look at the rb20 ones u will see its the plenum with standard runners welded on, suppose u have to remember the postage is another $175 on top.

I concure....looks better than the greddy knock off.

But then again..they could show you a Jun one and give you one of theirs.....

[Blitz]

I agree with MintR33 - For around the money they are asking when you take into account the cost of freight, you can pickup a Genuine Greddy Inlet Plenum kit - Much wiser option

[700HP-GTR33]

http://www.nengun.com/trust-greddy/intake-...-nissan-skyline

[jonnob55]

Thanks guys, looks like i will be going with the genuine greddy then!

[zertek]

I had one of these jun copies installed on my rb20det. It looked to me like the standard runners had been welded on... it was a very good plenum and even used velocity stacks.

but for a couple of hundred or so extra, would be good to go a genuine greddy...

[Cubes]

There's another jun copy thats a larger version.

I've seen the larger rb20det jun copy plenum. Its quality was actually pretty damn good. Velocity stacks inside, welding was clean; no noticable seat of the pants loss of down low but a hell of a lot more up top.

It wasn't a 'bolt on' and required a few mods to get it all working.

Also.. $700 is a bit rich. They can be had for $400ish.

[Ryno]

I've just purchased one of these (with a 80mm Throttle Body) for my RB25DET. I'll let you know how it looks, when it arrives.

Ryno

[T04GTR]

actually doesnt look to bad atleast its sheet metal.

[redevil]

get greddy copy for 395.... just on a further note i have seen an rb25 one in person and they are pretty good quality

Edited September 25, 2007 by redevil

[Bass Junky]

GTTR34 (Matt) has one on his R34 GTT I believe.

[redevil]

san at motive performance has one down there that he'll sell for 700 or so i think he said

[STATUS]

pretty sure those JUN copies are made in Thailand or Taiwan... cant remember...

Greenline sell the genuine Greddy ones for $885 so just go with that. Atleast its a proven Japanese brand and you will be supporting the company who has ACTUALLY come up with the design and done the research and development...

yeah, look at JET200 (ignition DVD project car) it had a millenium motorsports custom plenum on it, replaced it with a GREDDY one and bang .... more power everywhere low, mid and top..... there is a lot more to plenums than just a pretty weld job....

[redevil]

has anyone actually run one of these?? are they any good??

Edited October 12, 2007 by redevil

[Marco-R34GTT]

So these plenums fit on an RB25 neo as well??

[Ryno]

I received my plenum (with 80mm throttle body) about a week ago, it definitely looks the part, and the workmanship is top-notch.

I'm fitting it to the car in two weeks time, so I will let you know how it goes.