Jump to content
SAU Community

C210 C211 240k 280zx Wanted!

coupe72001
 Share

Recommended Posts

coupe72001 Mentor

coupe72001

Posted
Posted

Im looking specifically to buy these cars. Prefer complete original cars but will consider almost anything including parts and engines etc.

Give me a call on 0410 842 016 or [email protected]

Australia-wide fine but VIC, NSW and QLD are easiest for me.

Thanks

Drew

Link to comment
https://www.sau.com.au/forums/topic/180179-c210-c211-240k-280zx-wanted/
Share on other sites
coupe72001 Mentor

coupe72001

Posted
  • Author
Posted
with body kit etc.there is a 3.1litre stroker TURBO 240k.

$3000 on ebay.....

fkn weapon it would be!!!

Seen it... an I agree that its pretty wild... but too much and not original unfortunately. More looking for grandma's old C210 growing cobwebs under a tree somewhere.

works 510 Experienced

works 510

Posted
Posted (edited)

hahahahah....

Not a good idea asking that on a forum where people actually know what these cars are worth :(

Try local and asking people on the roads if they want to sell it. I brought my old smashed coupe buy knocking on their door and ive picked up a mate a datsun 1600 by leaving a note on the windscreen.

Edited by works 510
coupe72001 Mentor

coupe72001

Posted
  • Author
Posted
I recently picked up a 280ZX for FREE. Complete car and running all for the cost of the tow.

Done deal.

Ill organize a tow. Please give me a call on 0410 842 016 or get me at [email protected] and we'll sort the details.

Thanks so much,

Drew

Factory 5 Mentor

Factory 5

Posted
Posted

yeh drew!

he was just saying what a good deal he got.....

i bet ya feel abit down now!

i have a set of GENIE III L6 extractors i got for $100 you can have for the same it you like?

the came of a carbie L26 powered 260C at my local wreckers....

coupe72001 Mentor

coupe72001

Posted
  • Author
Posted
yeh drew!

he was just saying what a good deal he got.....

i bet ya feel abit down now!

i have a set of GENIE III L6 extractors i got for $100 you can have for the same it you like?

the came of a carbie L26 powered 260C at my local wreckers....

Right.... well if ghosty gets sick of it taking up space at the workshop, or he wants to part it out, he'll know who to call!

Ill let you know about those extractors too mags.

D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 Gtt Wheel Offset Advice

      By GTSBoy · Posted

      What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • silviaz
      R34 GTT idle problem

      By silviaz · Posted

      I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • Kinkstaah
      R34 Gtt Wheel Offset Advice

      By Kinkstaah · Posted

      This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • AdiR34
      R34 Gtt Wheel Offset Advice

      By AdiR34 · Posted

      Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...