Jump to content
SAU Community

Recommended Posts

okay since ive sold the onevia and now got a r32 skyline 4 door ;),

all my 4 stud & s13/180sx stufff has to go!!!!!!!

prices are firm unless stated otherwise..

item1got a pair of 4x114.3 bronze koya drift teks in 17x8 +34

offset.

comes with 225/45 tyres 1 side 50% the other 20% or so.

price update $550 with tyres take it as it is these cost me $565 + delivery from adelaide under a year ago :D

79387541om0.th.jpg

driftteks1dd1.th.jpg

more pics upon request guys,

item2 25mm HUBCENTRIC bolt on spacers 4x114.3

only problem with these spacers is that the bolts on the hub are mx1.5(i think) and not mx1.25 like nissans.

correct nuts will be supplied tho so it doesn't matter :worship:

after $90 for the pair pick up in syd.

item3 S14 SR20DET fuel pump (take off a 95 model ADM 200sx) roughly 85XXXkm

after $20 good upgrades for you NA and CA boys..

item4 S13/180sx rear hubs x 2 (left & right) with good bearings. bought off liz from the forums.

was originally for my 180sx which had a suspected rear bearing problem but never got a chance to fit them.

after $30 the pair pick up in syd.

item5 s13 sr20de na standard extractors with o2 sensor.

after $20 pick up in syd.

item6 also got STOCK S13/180sx catback exhaust, good to clear them defects $60 :teehee:

item7 180sx sr20det front brake setup consisting of rotors,calipers & pads.

after $80 pick up in syd

item8 ISC front coilovers to suit s13/180sx used for 5000KM, sold the car so NLR. $400 pick up or extra for delivery

gonna have r32 gtst stockies for sale in a few months time.. may swap for a nice set of dished rims + cash of course..

photo's will be up soon or upon request

all items can be shipped interstate at buyers expense.

pm reply here or call/sms (if i dont answer) 0413544494

thank you for your time.

Edited by whyte

hi mate im intrested in the rims as i req some smaller offset rims. could you be able to measure the width with a tape mesure and let me know by pm.

thanks brentt.

also how much would it cost to post to wagga wagga or would a arangment be better.

  • 11 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
×
×
  • Create New...