Jump to content
SAU Community

Recommended Posts

Just noticed on shitehouseNS.com that the Toyota Car Club are putting on a Nissan v Toyota Dyno Day at Boostworx on the 15/9

Soooooo calling all HIGH KW Skylines........LOL Munro, Darren, Darren, Matt, Dan and the rest of you, get the cobwebs off and roll down, i think i'll be there but just giving you guys a heads up!!

Link below

http://www.nissansilvia.com/forums/index.p...howtopic=252401

It starts at 10am and finishes up at 5pm.

Register with the www.toyotacarclub.net forums and then proceeded to register your intent to run with the details of your car (brand, make, model) at the following link.

http://www.toyotacarclub.net/forum/YaBB.pl?num=1186751226

Doing so enables you to get the dyno run for $35 vs $40.

Link to comment
https://www.sau.com.au/forums/topic/180801-nissan-v-toyota-dyno-day/
Share on other sites

  • Replies 105
  • Created
  • Last Reply

Top Posters In This Topic

Add to that list snyper and hostile if we can get them out there.

I should be making over 210 RWKW by then as well, but i suspect that will not be anywhere near enough kw's to make any competition.

I'll be there (well, stagea anyways) on the monday 10th for final tune n stuff.

200awkw Id expect........ around 1 or 1.1bar

then thrusday 13th out comes the last (left) kneecap + high tibial tubercle osteotomy

so, on that note, have fun on Saturday 15th as I know I sure wont be (havn fun that is)

hopefully be there. might even put the 32 up for a run. hoping for 250rwkw + by then. depending on what my car has on it eg injectors and fuel pump.

dyno very shortly to find out once the return from jesters with turb installed.

Just noticed on shitehouseNS.com that the Toyota Car Club are putting on a Nissan v Toyota Dyno Day at Boostworx on the 15/9

Soooooo calling all HIGH KW Skylines........LOL Munro, Darren, Darren, Matt, Dan and the rest of you, get the cobwebs off and roll down, i think i'll be there but just giving you guys a heads up!!

Link below

http://www.nissansilvia.com/forums/index.p...howtopic=252401

am i one of those Darrens?

just put 323kws at Boost worx this morning.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Unfortunately haven’t taken pics yet after it was finished. All the edges are hemmed nicely, just had to cut holes for the gear shifter and seat bolts and seat belt bolts in the rear. The molds seem like they’re done with steam and a layer of glue on the underside to hold a bit of shape but still soft enough that it’s a good fit when it’s all pressed down.
    • When's the rear mounted turbo kit coming? Needs dose and V8 chop idle lol.
    • I was very unimpressed with how the car came up from the A pillar forward, before I hit things (twice). It all has to go. It had to go, but now it has to go... more. So we finally found the very first Shennanigans with the entirely perfectly setup engine that had no problems being pulled apart to improve on 'was perfectly fine'. Cam bearings looked a bit... stock. Which isn't entirely bad given they were stock and this is a ~20 year old engine. So new cam bearings are on the way because it's somewhat difficult to get to this stage to do it later, and it will trash the block. It was quite unusual that it wasn't done when the perfectly new-looking VCM cam was originally installed by [unknown] What IS unusual is the cam that was installed there was advanced SIX degrees. As to why there is no way to know.. however it could have been @Dose Pipe Sutututu's mate who wanted a larger cam sound but also wanted it to come on earlier to be more usable. This is my dyno sheet with the previous setup - This cam is not supposed to peak until 7000+ RPM, according to VCM. This is what lead me down the whole 'my heads/intake setup is running out of puff and can't support the cam' line of thinking to begin with. Anyway too late now - New cam is in! It could be rather funny if this smaller cam acts like a larger cam because it isn't advanced six degrees. In the spirit of everything is working amazingly - the COMP cam required no dialling in whatsoever. It was about 0.5 degrees advanced, which seems pretty bang on. Any adjustment either way would be further out. I'm told as a chain breaks in it ends up regarding back about 0.5 a degree as the chain breaks in, making it bang on. In the spirit of everything was previously working amazingly - The timing gear that was taken out turned out to be was an N-Motion double timing chain kit, with adjustable cam gear (which is how it was 6 degrees advanced) and all looks entirely perfectly new. It also had a Torrington bearing, which was one of the reasons I ended up getting the Cloyes kit which they used in the C5R 24 hour racecar - Because I couldn't confirm what was in the engine when talking to Tony Mamo. I did believe however it was a Double chain kit of some kind... but found no supporting documentation or evidence for it.
    • I recently did this to my R33 with the full set from Car Mats Direct, they can't do the vinyl anymore that's advertised on the website due to a supplier issue so I ended up with the Black Loop Pile which looks great. I went all out with rubber sound deadening sheets from Repco and also added the sound deadening foam layer option with the carpet. Makes a world of difference and got rid of all the weird smells in the 29 year old interior. It was a bit of work but I'd 100% recommend it, Car Mats Direct had awesome customer service and quick postage. Replaced my seats with some sporty ones from Autotechnia while I was at it, feels like a new car.
Ă—
Ă—
  • Create New...