Jump to content
SAU Community

Globe Replacement With Leds

666DAN

By 666DAN,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

666DAN Grand Master

666DAN

Posted
Posted

Due to the volume of questions relating to installing the LEDs here is a basic "How To"

Please note the section on splaying out the leads on the globe and contacts in the base to ensure good electrical connection it also covers the orientation of the bulb this is a stumbling point for many people and results in 11 billion PM's about globes that don't work (but really do) :rolleyes:

100_2698small.jpg

100_2711small.jpg

Twist the bulb holder to remove (T10 and T5 shown)

100_2700small.jpg

100_2712small.jpg

Pull the bulb out of the holder, they *will* come out some are in tight

100_2717small.jpg

100_2704small.jpg

Sometimes the lead on the globe will fall into the recess in the plastic, splay it out slightly to guarantee electrical contact. Some of the bases are quite old and could also do with splaying. This is the number one reason for bulbs that "appear" not to work and actually are fine.

100_2705small.jpg

100_2714small.jpg

Fit the LED globe by pushing it into the base (T10 and T5 shown)

100_2708small.jpg

100_2709small.jpg

Twist the globe and holder back into the cluster (note the location of the black dot) Now this is the important bit; LEDs *only* work in one direction, so if it doesn't light up you need to turn the holder 180 degrees (note dot in second picture) Do *NOT* remove the bulb, just rotate the holder as then you won't get mixed up what direction you had the LED in the first place.

Plug everything back together after making sure everything lights up, congratulations you're done!!!!

Link to comment
https://www.sau.com.au/forums/topic/181486-globe-replacement-with-leds/
Share on other sites
  • 3 months later...
  • 2 months later...
gumflapper Grand Master

gumflapper

Posted
Posted
666Dan

Get your supplier to fit a bridge rectifier and you won't have to worry about polarity problems.

do you know what a bridge rectifier is... what it does? how it works... do u know what a diode is? how it works?

666DAN Grand Master

666DAN

Posted
  • Author
Posted
666Dan

Get your supplier to fit a bridge rectifier and you won't have to worry about polarity problems.

It is possible, but you'd see 300% increase in price :thumbsup:...and as above, that's for making DC from AC so not much use in this instance

NA_Goodness Grand Master

NA_Goodness

Posted
Posted

I'm trying this now. Dan, how much are your LED's? Tried a spare one that was sitting around the house, lasted 3 seconds before it blew... Now I'm struggling to sind some what would fit. Found one, but if yours are cheaper, I might buy some off you. I live in WA, how much would postage cost?

  • 10 months later...
turbo_brian Community Regular

turbo_brian

Posted
Posted
Tried a spare one that was sitting around the house, lasted 3 seconds before it blew...

You need to make sure it's got the right voltage rating, you need 12volt globes, or 4 x 3 volt in series for the voltage to work correctly, otherwise PING and she will blow.

I noticed in the pictures above that the globes look to be in series, so they would be 3-volt high-light LED's linked in series to allow them to take 12 Volts feed.

B.

  • 2 weeks later...
bloodsword27 Veteran

bloodsword27

Posted
Posted

hey dan the bulbs are in and work a treat. only question is that wen installed, on the right half of my tacho and speedo and lit up; the other half is either not lit or very dim. is there a fix to this or is it faulty globes?....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • njdgomez23
      How to fix centre console latch.

      By njdgomez23 · Posted

      After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • marni
      I need more than help to finish my R33

      By marni · Posted

      Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • r32-25t
      Attesa pump mount options / ideas? R32 gtr style.

      By r32-25t · Posted

      From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • GTSBoy
      R34 Manual conversion Speedometer

      By GTSBoy · Posted

      Have you looked at the workshop manual?
    • GTSBoy
      rb25 gearbox mount options - solid mount?

      By GTSBoy · Posted

      Hmm. I've gotten pretty good outcomes from talking to them about things that I've had go wrong or ideas for improvement. Have had a lot to say about the R32 FUCAs, and they have sent out some replacement parts for those, gratis, on a couple of occasions. Mind you, I have bought a couple hundreds of $ of replacement rod ends for them too!
×
×
  • Create New...