Jump to content
SAU Community

R33 Parts - Garage Clean Out

Bobjones

By Bobjones,
in Classifieds

 Share

Recommended Posts

Bobjones Mentor

Bobjones

Posted
Posted

Hi All,

Well I have sold my skyline and cleaning out the wreckage left behind...ALL items are pick up only...and relate to a Series 2 R33 that has done a genuine 76,000kms and all parts are in perfect working order otherwise they would have been binned, if you are unsure whether they will fit ask elsewhere. Please PM me with offers.

1. Leather gear boot and handbrake boot, got from Group Buy, never been fitted - SOLD

2. Stock Suspension, shocks and springs, no boots or bump stops - $40

3. Stock Brake Rotors, minimal wear (approx 1-2mm) do not require machining - $40 SOLD pending payment

4. Front stock Castor Rods - $20 ONO - SOLD

5. Stock Dump Pipe, Front pipe and cat incl heat sheilds - SOLD

6. S15 Mags 16x7 - One pair has new 225/50 done 50kms (they are cheap tyres ie $100 each) the other pair have old Federals 205's that will do one skid, barely legal. (Will post pics shortly) - $450 ONO

7. R33 Starter Motor, came off engine done 70K, tested and perfect working order (was only swapped out trying to locate electrical gremlin) - $80 ONO

8. R33 Stock BOV - $20 ONO

Cheers

Neill

Link to comment
https://www.sau.com.au/forums/topic/181705-r33-parts-garage-clean-out/
Share on other sites
seriesII Mentor

seriesII

Posted
Posted (edited)

hey, my castor rods are gone as in, missing... can you post a pic of the fron castor rods if you have any?.. i think ill buyem any how :)

i can do pick up

Edited by seriesII
  • 2 weeks later...
Bobjones Mentor

Bobjones

Posted
  • Author
Posted

BUMP,

People I am back from the Vic Dutton and these can be picked up this weekend. Apologies for the omission of photos, those items not picked up will be photographed this weekend and posted, apologies again for the delay.

Please PM me with offers and to get pick up details. My mobile is in the signtaure below!!

Cheers

Neill

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Hypergear Turbochargers and High flow Services Development thread

      By Dose Pipe Sutututu · Posted

      Here's one I help build and tuned a decade ago, Garrett  GTX3071R Gen 1, T3 twin scroll 0.83 rear housing. Went from larger 272 cams down to smaller Tomei Poncams to help with the low end. S13 non VCT motor. Car was purpose built for the track, hence low down was the focus. Note the actual dyno chart shows lower boost, however the EBC and boost gauge showed 1.9Bar (Ignore the torque, I was young and didn't know how to set derived torque)  
    • hypergear
      Hypergear Turbochargers and High flow Services Development thread

      By hypergear · Posted

      I’m doing some side developments on SR20det S13 engines, its one my hobby cars used it to compare flow capacity of some smaller size wheels. SR20det is one of another JDM legendary engines I'm sure there are plenty of SR enthusiasts on this forum, I will share results some common turbo configurations here. a quick run down of what the car is: Wide body 180sx Type X with black top engine (blue). It has: Stock bottom end Haltech 1500 ECU 5-0 motorsports trigger kit Kelford SR20DET Beehive Spring with Titanium Retainers Kelford Cams SR20DET S13 188-B 268/272 Cams G25-660 Turbocharger in T2 .64 rear housing internally gated ARP Head studs MLS head gasket 1000CC ID injectors Walbro 450L Fuel pump Front mount cooler kit JJR’s 3 inches turbo back exhaust (its too short for the 180sx it had to be extended) Pump 98 fuel Hub Dyno tune So far made 270rwkws at 22psi full boost by 4500RPM. Engine is very knock limited hence a pretty bad looking top end. From previous experiences it seems like SR20dets are happier with bigger size turbine, some thing like a GT30 would make way better top end, but on same time response is lost. It won't be a problem with S15 VCT engines. I'll be testing alternative turbine housing, turbine wheel and possibly dump pipe options for extra flow to resolve the problem and of course E85 would resolve all the issues.            
    • cardre
      My R32 Money Pit & The Headaches That Come With It

      By cardre · Posted

      Awesome writeup and details. Thanks for sharing the story so far. I can relate to parts of it with my previous car and some of the issues I had to deal with.
    • Milkmun
      NC MX5

      By Milkmun · Posted

      Wow the colour matched hard top completely transforms the car. Are there any nice front lip options for the car or is that off the table?
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Generally yes but for some reason I've been ruthless this time around!  I might even need to do another tip run after the way I've finally been able to hit the delete button on shit I've stepped over, stepped around and tripped over for the past 10 years!
×
×
  • Create New...