Jump to content
SAU Community

Recommended Posts

hey guys here is one of the pics in the tutorial..you can see the blue plug lying there @ the back...just wanna know where it goes. i already have the intake on. see above. any help is muchly appreciated. Hame :D

post-36645-1222726845_thumb.jpg

  • 1 month later...

has anyone actually fit top feed injectors to this manifold..? i did and there leaking. i used standard rb20 seals.. any idea's

i seen collars u can get to put in there ive seen ppl use on sr20's.. cant find em anywhere though

  • 3 weeks later...
Great thread, answered all my questions regarding this install.

Started her up yesterday, idles smooth as silk :laugh:

Can't wait to try her on the road, f**king winter here now...

motorrum_081219.jpg

Dude, looks like you hooked up your coolant bleed valve. Where did all the hoses go?

You block off the coolant bleed. Most of the hoses are covered in this thread have a read from page 1 :laugh:

Sydney Kid said it wasn't a good idea in one of his posts. I'd like to keep as many of the factory bits as possible.

But if I can block it off, it'll be blocked off.

Dude, looks like you hooked up your coolant bleed valve. Where did all the hoses go?

I took a good look where the water hoses for the bleed valve goes, before i took the old plenum off.

Didn't like the idea of not being able to bleed the air out of the cooling system

water_bleed.jpg

plenum_install.jpg

This way you don't have to block off any pipes. Just remember to mount the bleed valve so its the highest spot on the cooling system.

Edited by WilYawn

Why hasnt this been stickied yet :P

lots of good information, should be a sticky in either this thread or the DIY/Tutorials thread really

Appreciate the guide, will come in handy when it comes time to put mine on

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Some of them keep working fine. 9 out of 10 of them end up causing an absolute misery bleeding the system and get thrown on the workshop floor in a tantrum and never thought about again because they were never really needed and just added crap to the car that we could have done without. Same-same with HICAS, A-LSD, and various other stupidities that over eager 10x engineers thought we had to have.
    • Not required but appreciated. Super Coppermix Twin even the non-competition model feels like the pedal is noticeably heavier than stock which was pretty well judged IMO. I'll be swapping in the Nismo operating cylinder soon to see how that feels.  Personally I haven't felt anything that justifies replacing the damping loop, at least compared to more modern stuff where the clutch delay valve is actually quite noticeable.
    • He made that comment in my thread - In my case the vents ARE to lower engine heat, when the car is not moving, which is the only scenario I have heat problems with the aircon on, sitting in traffic, on 40C+ days. I can't imagine a scenario that this NC needs any at this point in time. I do not know if it will actually make my cooling when the car is MOVING worse, and I sincerely hope that won't be the case. If it does, well, um, f**k.
    • Nice, thanks. Thats why I was asking, there'd been a fair bit of discussion in the E90 world about vents and where it makes sense to put one (ie, over the filters is not great as that is inline or slightly behind the struts and in higher pressure area). I struggle with air flow and pressures. It sill weirds me out that a radiator in the boot can work. 
    • Neither really Vents, when located in the right place, will lower the engine bay "pressure", as air has a path to escape, thus lowering the engine bay pressure, thus.....improving the efficiency on the coolant stack (read: IC, condenser, radiator) This is why the Blits vented bonnet on my 33 worked so well, the vent was in the front 1/3 of the bonnet, which put it right after the radiator  If the vents are to far back toward the windscreen, which is a high pressure zone, it can actually force air into the engine bay, causing higher pressure and effectively loosing efficiency on the cooling stack, like the fab of raising the rear of the bonnet, which does allow heat to escape, but only when the car isn't moving  There's heaps of cool "fluid dynamics" info out there, but, I'll attach a video of a 'Merican joint that focuses on "Miatas" as I found it when looking into vents for mine, they explain it way better than me  
×
×
  • Create New...