Jump to content
SAU Community

Recommended Posts

Hi all,

Alright here is the problem: vehicle R32 GT-R

Occasionally the HICAS light blinks on for a second or two and the steering becomes hard only while the light is on, steering goes back to normal and light goes off. Recently this has been occuring more with some instances of the light staying on consistently and blinking off for a fraction of a second, while at the same time a "knock knock knock" can be heard. The steering will pulsate with the same frequency as the knock, which is particularly noticable while turning as the steering wheel rocks back and forth.

Conditions:

Hot or cold running - P/S fluid hot or cold

Recently, under acceleration

Recently, when turning the headlights on to low or high beam

When turning-in

When going over a bump, only occasionally/hard bumps

Recently even while idling doing nothing

Any speeds

Observations:

P/S fluid is between the add and full marks, recently topped up, does not appear or smell burnt

P/S pump belt is tight with no wear marks from slipping, can not hear squealling

Can feel the knock when holding on to a hose from HICAS valve body which runs to the P/S fluid cooler lines in front of the radiator

Tyres are 265's

Really need some help on this as it is becoming dangerous. No one around here knows about these systems(HICAS), but I do suspect something more common.

Link to comment
https://www.sau.com.au/forums/topic/181836-power-steering-problems/
Share on other sites

You may have a voltage droop, the hicas is very sensitive to low volts.

Check what you are getting at the unit itself, and with the electrical system loaded.

You may need to provide a better earth and a clean of connections.

james.

ps, do the diagnostics as well. It will tell you the logged faults.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I think my main complaint with your idea is that there is a veneer of idealism spread across it. You want the simple numbers to make it easier, but all they will do is make it easier for someone to come to the wrong conclusion because the fine details will kick them in the nuts. As it is right now, the tiny bit of arithmetic is NOT the obstacle to understanding what will fit and what will not fit. The reality of trying it is what determines whether it will fit. If you had a "standard rule" that R34 GTT guards have that magic 100mm space from the hub face to whichever side you were worried about, and someone said "excellent, this wheel is only 98mm in that direction, I'll just go spend $4k on them and jam them on my sick ride".....they would just as likely find out that the "standard rule" is not true because the rear subframe is offset to one side by a fairly typical (but variable) 8mm on their car and they only have 92mm on one side and 108 on the other.
    • It still combines inches with mm, especially when you have .5 inches involved, and mm and inches that can go in either direction. This would give a clear idea on both sides of the rim, right away, with no arithmetic. Even better if somebody gives you the dimensions of the arch of multiple cars. i.e GTR may be 125mm, a A80 Supra may be 117mm, or something along those lines. Yes, you can 'know' that going from a 10in rim to a 10.5in rim with the same offset moves both sides about 6mm, but you still have to 'know' that and do the math. Often it's combined. People are going from 9.5 +27 to 10.5 +15. You may do the math to know it, but if it was going from (I had to go look it up to be sure) 241mm/2 - 27 - 93.5mm from the center line to (more math) 266/2 - 15 (118mm) from the center line. Versus 93mm vs 118mm. It's right there. If you know you have a GTT with 100mm guards you can see right away that one is close to flush and the other absolutely won't work. And when someone says "Oh the GTR is 120mm" suddenly you see that the 10.5 +15 is about perfect. (or you go and buy rims with approximately 118mm outward guard space) I think it's safe to say that given one of the most common questions in all modified cars is "How do offsets work" and "How do I know if wheels will fit on my car" that this would be much simpler... Of course, nothing will really change and nobody is going to remanufacture wheels and ditch inches and offset based on this conversation :p We'll all go "18x9+30 will line up pretty close to the guards for a R34 GTT (84mm)" but 'pretty close' is still not really defined (it is now!) and if you really care you still have go measure. Yes it depends on camber and height and dynamic movement, but so do all wheels no matter what you measure it for.
    • But offsets are simple numbers. 8" wheel? Call it 200mm, near enough. +35 offset? OK, so that means the hub face is that far out from the wheel centreline. Which is 2s of mental arithmetic to get to 65mm to outer edge and 135mm to inner. It's hardly any more effort for any other wheel width or offset. As I said, I just close my eyes and can see a picture of the wheel when given the width and offset. That wouldn't help me trust that a marginal fitment would actually go in and clear everything, any more than the supposedly simple numbers you're talking about. I dunno. Maybe I just automatically do numbers.
    • Sure! But you at least have simple numbers instead of 8.5 inches +/mm, relative to your current rims you do maths with as well, and/or compare with OEM diameter, which you also need to know/research/confirm..
×
×
  • Create New...