Jump to content
SAU Community

Recommended Posts

There well supported but a tad basic for street R33(Stinger version) and waste spark etc.You would need the top model to do it right so best to look for a plugin like PFC or Wolf etc. You need Idle speed,VVT,, boost, Aircon request,and closed loop minimum for a nice road car, Stinger uses it outputs for tacho,fuel pump control etc leaving you short on outputs.Ive seen fuel pumps hard wired cause theres no outputs left so if going EMS look for their topend model,and as your saying the price is cheap i think your talking Stinger.The real upside it EMS are fantastic ppl to deal with.

Link to comment
https://www.sau.com.au/forums/topic/181842-ems-ecus/#findComment-3302894
Share on other sites

Thanks NIB. I think in the end I may go Wolf, just a shame the dashes are not availble until they find another supplier. IMO PFC's are not really a good choice considering what they are and feature for the prices people are asking, you need to run Z32's with them which is an additional cost and nothings guaranteed because its all 2nd hand now. In comparision (for cost) there are many better choices, the only thing they have going for them is the support for tuning.

Anyway my intake/turbo setup is..

HKS GT2530

SARD BOV

3" Turbo back exhaust (inc stainless steel dump/front)

Hi flo cat

Pod

With an ECU i suppose i should get around 300rwhp?

Link to comment
https://www.sau.com.au/forums/topic/181842-ems-ecus/#findComment-3304298
Share on other sites

will be putting one of these in my 32 very soon spoke to a mechanic who tunes these all day everyday he was telling me he tuned a 32 rb20 only mods he had was pod filter after market intercooler and 3'' cat back exhaust and the thing pulled 197rwks on 10psi will let yas know what mine pulls out when i get it done

Link to comment
https://www.sau.com.au/forums/topic/181842-ems-ecus/#findComment-3305246
Share on other sites

will be putting one of these in my 32 very soon spoke to a mechanic who tunes these all day everyday he was telling me he tuned a 32 rb20 only mods he had was pod filter after market intercooler and 3'' cat back exhaust and the thing pulled 197rwks on 10psi will let yas know what mine pulls out when i get it done

I find that very hard to believe.. must have been a very generous dyno..

Link to comment
https://www.sau.com.au/forums/topic/181842-ems-ecus/#findComment-3305471
Share on other sites

will be putting one of these in my 32 very soon spoke to a mechanic who tunes these all day everyday he was telling me he tuned a 32 rb20 only mods he had was pod filter after market intercooler and 3'' cat back exhaust and the thing pulled 197rwks on 10psi will let yas know what mine pulls out when i get it done

Will need a good Turbo for that.

Link to comment
https://www.sau.com.au/forums/topic/181842-ems-ecus/#findComment-3305930
Share on other sites

stinger is a great little ecu for a basic setup converting a car on a carby to an efi setup.

For a nissan it's not a good move.

how come??

my car has made over 400 hp@ 27psi on NIB's dyno with the stinger. stock internaled rb20...

my best mate converted a series2 rb25 into his r32 with gt30 and stinger and that made close on 400 aswell

there an awesome bang for buck ecu, u dont need to wire it up as a standalone it can be pickybacked aswell meaning you keep a few outputs.

they have just realesed a whole new range aswell which would be worth looking into

Link to comment
https://www.sau.com.au/forums/topic/181842-ems-ecus/#findComment-3306052
Share on other sites

how come??

my car has made over 400 hp@ 27psi on NIB's dyno with the stinger. stock internaled rb20...

my best mate converted a series2 rb25 into his r32 with gt30 and stinger and that made close on 400 aswell

there an awesome bang for buck ecu, u dont need to wire it up as a standalone it can be pickybacked aswell meaning you keep a few outputs.

they have just realesed a whole new range aswell which would be worth looking into

I like the stinger myself , I had one not long ago running a turbo efi converted A14 in a datsun 1200 ute.

Power numbers themselves aren't a measure of how good an ecu is, the setup is a complete pain in the ass compared to things on the market that have plug in abillity to suit the RB nissans. But If you like mucking around then why not?

hows the fuel ecconomy on yours?

Link to comment
https://www.sau.com.au/forums/topic/181842-ems-ecus/#findComment-3306293
Share on other sites

I like the stinger myself , I had one not long ago running a turbo efi converted A14 in a datsun 1200 ute.

Power numbers themselves aren't a measure of how good an ecu is, the setup is a complete pain in the ass compared to things on the market that have plug in abillity to suit the RB nissans. But If you like mucking around then why not?

hows the fuel ecconomy on yours?

yeah true i can understand the wiring up as being an issue to some, but it made life a hell of alot easier to me (managed to ditch most of it from the exhaust side)

agreed on the power thing but 27psi on the internal map sensor... no need to upgrade to bigger sensor unlike some of the more expensive ecu's on the market.

fuel ecconomy is like any hard tuned car,I see 350km to a tank with light driving and with full throttle hill runs type driving (on off on off) ive seen up to 400 a tank :rolleyes:

Link to comment
https://www.sau.com.au/forums/topic/181842-ems-ecus/#findComment-3306403
Share on other sites

will be putting one of these in my 32 very soon spoke to a mechanic who tunes these all day everyday he was telling me he tuned a 32 rb20 only mods he had was pod filter after market intercooler and 3'' cat back exhaust and the thing pulled 197rwks on 10psi will let yas know what mine pulls out when i get it done

You must be kidding. Is that even possible with such mods? I find it hard to believe man. As bubba said, must be a very generous dyno.

Link to comment
https://www.sau.com.au/forums/topic/181842-ems-ecus/#findComment-3306618
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 1. I can't see a location on your profile but you do mention GBP so I'll assume you are in UK. In Australia, CBC make a timing belt kit with the gears and idler and tension bearing and that is what I use without any problems. I'm sure OEM or HKS are also fine but I wouldn't pay extra for HKS over anything else. 2. Yes, I would always change the idler and tensioner and the stud and bolt that hold them in. Assuming they were all done last time it is highly unlikely you would have a problem, but they are very cheap to add to the job considering the time it will take anyway.  3. No, you don't need to lock them as such (I think that is more for engines without timing marks), but you should make sure they move as little as possible once the belt is off as you can hit pistons on valves if they move too far. As always, make sure you line it all up to top dead centre with the timing marks aligned before you take the old belt off.
    • How to wreak havoc at a bogans party... Swap out the goon bag hanging from the clothes line with oil bag... Watch chaos ensue during Goon of Fortune....
    • Hey everyone,   I’m looking for some advice on replacing the timing belt on my RB25DET Neo-powered 1998 Skyline. The engine was fully built about five years ago, including a fresh timing belt, water pump, and other essentials. However, since then, the car has only covered around 2,000–3,000 miles. It’s currently making around 650hp.   Even though the mileage is low, I know timing belts have a time-based lifespan too, and most recommendations suggest changing them every five to six years or 50,000 miles. Since I’m at that time mark, I’d rather not take any risks and plan to swap it out soon.   A few things I’d like to hear opinions on: 1. What’s the best belt for this setup? Should I go with an OEM Nissan belt, or is the HKS fine-tune a better choice given the power level? 2. Would you bother replacing the idler pulley and tensioner at the same time, or only if they show wear? 3. When swapping the belt, is it necessary to lock the cam and crank gears in place, or is lining up the timing marks enough? I’ve seen different approaches, and I want to make sure I do it right.   The water pump was changed with the rebuild and isn’t run off the timing belt, so I don’t see a need to replace it again. I just want to make sure I approach this the right way.   Any insight would be much appreciated. Thanks!
    • How does this compare to the internally gated g25-550 in terms of power production at same psi and spool
×
×
  • Create New...