Jump to content
SAU Community

Cruise Alice


Sklyn
 Share

Recommended Posts

No worries Kurt, Good luck with the car and have safe trip.

Cammo, still coming out with me? And Ryan better be taking the green machine out to the drags :blink:

I saw that R32 at caltex 3 odd weeks back. Looked nice but i drove by it. Total write off or slightly repairable?

Link to comment
Share on other sites

Hey guts did a full re spray of the pulsar today just in red with white rims look so much better check out the pix, all up i used two big cans of red 6 lil cans of red and 2 white for the rims cost bout $150 and took bout 4-5 hours

post-50230-1226211993_thumb.jpg

post-50230-1226212092_thumb.jpg

post-50230-1226212179_thumb.jpg

Link to comment
Share on other sites

Right'o guys, on Saturday lets meet at 12 at Hungry's before going to drags. I think it starts at 2 so that will give us time to get a feed and whatever else you want to do.

Spread the word!!

Link to comment
Share on other sites

I might be out. Depends how hot it is. Yet, i can barly see the ranges from town with all this dust in the air. If it rains, it's going to be a stinka

Link to comment
Share on other sites

Some good and bad times from us all but good turn up.

Hopeing for better times tomorrow for myself as i'm .300 slower then my PB. So less rain, more track time.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
    • You can just get the injector bosses, which allows top feeds to fit. He can use the same injectors without issue, like these (another option): https://rocketindustries.com.au/af59-2210-rb25-fuel-injector-inserts     The Racework ones look a bit better: https://www.nzefi.com/product/raceworks-lower-injector-mounting-boss-kit-for-r33-rb25det-s14-s15-sr20det/   You could also just get a similar kit like the Radium one by Plazmaman: https://plazmaman.com/product/nissan-rb25det-r33-billet-fuel-rail/?srsltid=AfmBOoogfYq49X0fu2Wdbf8yOf6zt9egyPAif_gn3Qr3G8hzAphhTgOkO70  
×
×
  • Create New...