Jump to content
SAU Community

Recommended Posts

HERE WE GO PEOPLES!!

D.MODS - Cruise 2

Saturday 1st of September.

Late Night Run

MEET: Carosel Carpark upper section

Time: Sat night 11:30pm for 12am Leave

suggestion: bring a full tank, pop a no-doz before you come out and have a good coffee. Ya guna need to be alert for the hills run.

Dan.

Edited by YEHBOI
Link to comment
https://www.sau.com.au/forums/topic/181974-cruise-1st-september/
Share on other sites

Just a tip... at the top of mills rd can I suggest you turn LEFT onto canning mills rd, then left onto Chevin (awesome hilly rd thats like a rollercoaster) then at the end go left onto brookton hwy then left on canning rd (the road you want to be on). If you go left onto Canning mills at the top of Mills rd - that road through the bush part is very very dangerous and its not properly sealed. (I know how dangerous these roads are as I live in Roleystone).

ok.. i have changed how the details are being let out..

D.MODS - Cruise 2

Saturday 1st of September.

Late Night Run

MEET: Carosel Carpark upper section

Time: Sat night 11:30pm for 12am Leave

suggestion: bring a full tank, pop a no-doz before you come out and have a good coffee. Ya guna need to be alert for the hills run.

Meetpoints are as follows -

Caro, Midland, Morley, Freo

Dan.

Yeah there will be roos LOL Me and a few mates went up that way (obrien Road through to Mund weir road) only few weeks back and there were plenty of big ones. 2 near misses and that was even when we had slowed to under 60kph

Im not saying dont go....im saying be careful and i hope no one tries to be a hero but doing the run in record time. It will end badly :rolleyes:

I am sure people understand that there could be a chance of seeing aroo but like if u keep to the speed limit and just keep an eye out and be responsible you will be fine. I like the hills runs because i like windy roads and being able to hear everyones car echo off all the trees in the crisp cold air. its just gravy haha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welp, too late already committed to the cam cover breathers to be welded on. I did think about adding a catch can in line with the drivers side sump breather as a phase 2 along with a drain to the sump on the original catch can but with an inline ball valve so I can have it closed if needed.    Likely a single breather would have been enough but I think I’m overcompensating to hopefully not have to empty my catch can and clean up oil over flow every session.    out of curiosity has anyone actually measured crank case pressure before and after various mods? I’m considering adding a sensor for science 
    • Is it a dog or synchro box? I guess either way, if it is new and crunching in one gear only, it has to come out and go back to the shop to check/measure as there is either an assembly or manufacturing issue
    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
×
×
  • Create New...