Jump to content
SAU Community

Recommended Posts

hope I posted in correct section,

heres the run down on the details:

R32 - RB20 Silver Top

45V3 turbo

2.5" dump off the turbo i think, looks to turn into 3 or even 3'5 further up the system.. i havent measured it properlly yet

HKS fmic

standard fuel system (pump, reg and inject)

SAFCII

running 13.5 pounds.

is it worth upgrading the stock fuel pump to a 040 item? Im not too familier with what a standard gtst pump can take. It feels a bit lacking power atm, but its getting a good tune tomorrow but wondering if that should be something on my shopping list. not a big fan of buying shit and seeing no difference :wave:

Edited by YEHBOI
Link to comment
https://www.sau.com.au/forums/topic/182192-is-it-worth-upgrading-my-fuel-pump/
Share on other sites

Its always to be safe than sorry i would upgrade. I just installed a Nismo pump for $400. Came with brackets and new seal and will handle any future mods you may want to do down the track.

so your saying that the standard pump isnt really good enough so I could expect to see an improvment?

Well you dont want it to lean out and go bang. But im not sure if the standard pump is sufficient.

Get a new pump just to be safe. These car's are well over 15 years old and you never know when they could stop working. If you're on a tight budget, the GTR pumps should be fine, but they're also 15+ years old. Best to buy the right one straight up.

Since you are getting it tuned tomorrow anyways, check the afr vs rpm graph and see if you are suffering lean out issues.. Your tuner will be able to advise you further.

A gtr pump as djr81 and adam said would be fine for your application, as well as being the cheapest option, just another old pump though.

Walbro would be fine for it as well, as long as it is a genuine.

A bosch 040 would be good, but require more work to fit, as well as costing more.

Test and see what voltage your pump is recieving as well.. My car runs a gtr pump, but on the dyno was showing lean out bad with 220rwkw. Measured the voltage and it was ~10.2 and dropping under load. Wired in a direct feed to a relay switching from the original pump feed. Now sits over 13 volts. Its a lot of difference to how much a pump supplies.

james.

i got it on the dyno on sat and it got 155rwhp... and was displaying a fair bit of lean out, we then put the correct settings in afc and gave it a mild tune and it got 220rwhp but it was still leaning out a fair bit so it desperatly needs a new pump. So i have a 040 being installed in a couple weeks and then tuning it properlly and then il get it tuned again so i can up the HP..

Ive heard that the Bosch bumps are quite noisy compared to ones like the Nismo and Tomei pump can anyone with a 040 confirm this cause i also need a new pump but i don't want something thats really noisy where im going to hear it in the cabin....

I only hear a slight buzz from my intank 044.

When the pump was external it was loudish in the cabin. Internal ftw.

If your fitting the 044 intank of the R32 GTST you have to head down the local pirtek and grab a couple of appropriate fittings and then shove them on the lathe to machine the top fitting down to 5/16" and the bottom to suit the sock. A couple of hose clamps and suitable rubber to secure the pump and your laughing. :glare:

R33's.. They fit easy. Much deeper tank.

Ive heard that the Bosch bumps are quite noisy compared to ones like the Nismo and Tomei pump can anyone with a 040 confirm this cause i also need a new pump but i don't want something thats really noisy where im going to hear it in the cabin....

i can hear mine outside and in cabin... it's quite noisy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
    • Should have taken that opportunity to slot in a twin scroll turbo setup. Maybe next time.
×
×
  • Create New...