Jump to content
SAU Community

Recommended Posts

hey guys,

for sale

leather covered seats (not a retrim)

usually you can get these kits for 500 or so from ebay and what not, and you have to install the kit yourself. which means taking of the stock trim... without f**king up the foam (goodluck)

i did not buy this from ebay

inspection welcome. they definatly look the part

dsc00055hl3.jpg

pics of front seats

dsc00063hm7.jpg

Im selling it hwo you see it in the pic (NOT JUST THE COVER)

PRICES

Rear seats only = $270

Complete set = $350 PLUS standard seats in return Or If you have some nice bucket seats. depending on brand etc. cash your way

cheers guys

pm me

Edited by bLaQ.bOi
Link to comment
https://www.sau.com.au/forums/topic/183017-r32-gtst-rear-leather-seats/
Share on other sites

seat cover type

western suburbs in melbourne

had it for about 7 months in total

and my cars been of the road for just a bit more than 4

so there practically brand new

they havent seen many ass's

Edited by bLaQ.bOi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It's aftermarket. It also reeks of Honda Civic tryhard from 2003. But if you want one....then you want one.
    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
    • Kinda something I have been thinking about.  To be honest, we bought it already driving like that.  So there's no telling how long it actually has been driving like this.  Hopefully damage is too bad when we drop the pan.   I am having a hard time finding a site that sells the solenoid for the 5 speed auto, do you have any suggestions?
    • That'll be most likely down the road...  LOL  
×
×
  • Create New...