Jump to content
SAU Community

Recommended Posts

well i drive a R32 1992 Nissan gts-t i got a problem with my skyline and i want to see if anyone can point me in the right directions.

the car just dies on me when slowing down after a boost. for example in main street got speed bumps inbetween everyone boosts it, so other day i took out and i boosted it and then had to slow down for speed bump. Wasnt going fast around 50 probably less. so you let foot of accelerator to put on break, but the car dies on me. is it bcos i let my foot off to fast??

how can i stop that happening as its embarrising lol

Link to comment
https://www.sau.com.au/forums/topic/183071-skyline-cutting-out/
Share on other sites

if everyone jumped off a bridge would you jump off too?

does your car have a different blow off valve (bov) than the standard one?

that is the usual problem of stalling when coming to a stop/low revs etc.

to fix it, you need a plumback bov.

if none of this makes sense, take a pic of your engine bacy and post it here..

Doctor, it hurts when I do

this ...

It's probably a problem with the AAC valve can't react fast enough to open the air way for idle control.

Don't boost it - waste of time and energy... and fuel

if its actually cutting out (as in dies completely rather than loses revs) then its your AFM, do a search for "+solder +AFM" to see how to fix it

Thats not always true, mine was stalling, put the standard bov back on and hav'nt had a problem since.

Thats not always true, mine was stalling, put the standard bov back on and hav'nt had a problem since.

if you re-read my post you will see that i was referring the AFM fix to "cutting out" rather than "stalling",

99% of the time true "stalling" is related to BOV venting to atmosphere

Edited by WazR32GTSt
  • 3 weeks later...

The problem got really bad n my car today, could'nt even hold 100k's on the freeway, only thing i had done was fitting an airbox, i changed the afm over to a spare i have and i now have no more problems.

the only part i could see that could be opened on the old afm was where the plug is, took the screws out and gave it a wiggle and it came out, virtually no resistance considering there is 3 pins on there that should have been securely soldered inside.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, that is a helpful description, because that sounds exactly like a bleeding issue in the clutch....these are hard to bleed manually even when the damping loop has been removed. I'd suggest bleeding again....start by filling the master cylinder up and opening the bleed nipple. Come back and check every now and then that the master cylinder is not empty. Let it gravity bleed for a few hours and see if that improves
    • I replaced the whole clutch line with the chase bays braided hose, I think it removes that loop, is it the short hose that comes immediately off the slave or is there a drawing in the manual to find what you’re referring to? It was just re-bled when I upgraded to the nismo slave, old slave worked fine but I thought that might help, didn’t change a thing. It’s like the first half of the pedal is pushing air and then when it finally actuates the master the friction zone is tiny. Makes it practically impossible to launch the car
    • Yep, that was one of the things we learned fast in the past with our MX5. When you drive with the top down, you are effectively standing out in the sun, 100% of the time, and not getting in any shade (because roads aren't shaded generally!). Just like standing out in the middle of a field on a sunny 27C day is a bit of a bad plan, so is sitting in a MX5 without sun protection.
    • I also just ordered some Frankenstein bolts and side mounts to fit a hard top Just in case I do find one, basically so it doesn't need to be fixed to the car with only the front latch.......and then gaffa tape to keep it in place for the RTN journey from wherever I get it
    • If your temps are fine now, you probably won't have any issues with where your vents are as they don't look right up at the windscreens high pressure area, so any differences when giving it the beans for extended happy laps would be minimal, but, they should vent heaps when stuck in traffic  Much like how that reverse cowl on my SS let "visible" heat out when stationary, but, because it was basically at the windscreen my coolant temps on the Hwy actually raised because air was being fed into it at speed (110kph), to only come back down to around 90° when I got off the Hwy And your 100% correct about the NC currently not needing vents, but, if I was to add a turbo, and a oil cooler and intercooler in front of the condenserand radiator, and then take it to the track???? It is apparently a recommend requirement if I don't want to worry about coolant or oil temp issues, but, any of the above are possible scenarios, over time As it sits now, with the triple pass radiator and stock air conditioning system, I have absolutely no issues with either temps or air conditioning efficiency, I've been basically daily driving thie car for the last month, both on the Hwy, and peak hour, bumper to bumper traffic, but, that's pretty much expected from basically a standard engine  Talking about no issues daily driving, it was 39° the other day and I was sitting in bumper to bumper traffic on the M5 and then M7, with the top down, and with the air conditioning blowing nice cold air on my feet, balls, and face, well, there was one issue, my head and arms got pretty sun burnt Note to self: leave a hat and sunscreen in the car for such days 🤣
×
×
  • Create New...