Jump to content
SAU Community

Recommended Posts

You will find that your lights are crazed ( they have tiny little cracks on the lens from exposure to the sun) nothing short of changing them can fix it . Put your lights on at night and look in the lens you will the tiny little cracks . Polishing them fixes it for a little while, well makes them look better, not realy fixes them.

Mine are pretty bad on my R33, so i was going to replace them, but everywhere i inquire they all want anywhere from 350 to 450 per head light.

Is there anywhere I can get a set from that is not going to hurt my hip pocket to much. 700-900 for a pair of second hand oem headlights is a bit steep for me.....unless im cheap :D

I see some on US Ebay second hand ones that start low, but unsure if they will comply with AU standards?

Is it possible just to replace the headlight lenses wit new ones?? I know they're sealed on,

but are there places that heat off the old one and can fit a new one on? Can you buy just the lenses from nissan?

S2 Headlights new from nissan are $500+ each

Mine are pretty bad on my R33, so i was going to replace them, but everywhere i inquire they all want anywhere from 350 to 450 per head light.

Is there anywhere I can get a set from that is not going to hurt my hip pocket to much. 700-900 for a pair of second hand oem headlights is a bit steep for me.....unless im cheap :D

I see some on US Ebay second hand ones that start low, but unsure if they will comply with AU standards?

I have a good pair, no fogging and nothing broken you can have them for $350.

Get some really fine sandpaper, and some warm soapy water, and sand the headlights until you get a milky residue.

You can repeat again with a more corse paper, but still really fine.

Then cut and polish it with some good polish.

Has worked for me before, so give that a go.

Takes away the hazey yellow layer, and makes them pretty damn clear.

My xenons have gas marks on the inside of the lens, and from what i've heard the lights are totally sealed so apart from using a heat gun or something to open em up anyone else opened R34 len's ot cleaning the inside of them?

I use Meguires PlastX. It's a clear plastic polish specially designed for faded plastic and works pretty well. A few people i know thought i replaced the headlight. For $18 you cant really fault it except that you have to re-apply it every 1-2 months.

Edited by quiksta

lol 18 $$$$$$$$$$$$$

i just use 20 cents worth of polish and a bit of wax and it last for 2 months

has anyone else tried the wetrub with 1500 like mentioned earlier?

there is a new 29 $ dollar headlight kit i seen in supercheap but cant rem the company?

I know for the supras theres a mob that makes glass lenses for them. You can unseal the standard ones with a heat gun or oven or something, then replace the lens with a glass one and never worry about fading.

Any one made like a replacement glass lens for the skyline head lights instead of plastic??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ...just a note of warning, you shouldn't drive it about with the TCU in limp mode with only 3rd gear available ~ apart from the fact you end up sheering the ATF at the torque converter interface, the high clutch in these isn't especially the strongest, particularly bolted to the RB25DE mill...which is likely a 4AX01 box with lighter duty high clutch (the RB25DET got the bigger high clutch)...be careful out there...
    • Hoping to do similar mods to my RB20 once I get it running and reliable again
    • As you're looking at using a Link ECU, then large injectors are not a problem. But there's not really any need to go 1000s on an RB20 unless you're planning >>600HP on E85, which would seem unlikely. There are other options for injectors. The Xspurt ones are available from a number of places and you can get them in the mid 600s and 725cc, which is probably a sensible place to be. These are all EV14 based. If you are not using the stock AFM (at all, which would be the case with a Link) then a large turbo intake pipe to suit the ATR turbos is not an obstacle, so you should use one instead of a highflow. Results will be better.
    • Hey guys,  I'm after some advice and this here is the best place to get it imo. I was a member a looong time ago under another account, with a lost email address. Its nice to jump back on and see some of the same names still giving good advice.  I mothballed my car when i moved to perth in 2013, and after getting towed across the nullabor a few times it has officially done more km's on a trailer than under its own power. Now that i have started the process of tidying up and modifying it, i see the fruit available (and the fruiterers selling the produce) is different than back in the day. hence my questions, as i used to 'know' what to get and now, i'm not so sure. Engine wise the car (92 gtst) has a walbro 255, k+n, fmic, cam gears and and turbo back 3"exhaust. Wish list is a Hypergear high flow or ATR43G1, Link G4x and some newer injectors before a tune up. My goals are modest, only low 200's power wise. i know i could achieve this with less, but i've been swapping out old for new where i can. Every cooling hose has been replaced, along with mani gaskets, WP, thermostat and radiator, fuel pump and timing belt, tensioner and idler, and i rebuilt the steering rack. Regarding the injectors, the fruiterers all seem to sell what used to be considered quite large injectors. There are a lot of options for bosch 1000cc EV14's, and i would like to know if that is a suitable choice for my build. Is modern injector design good enough to run these at the low duty cycles that i likely would be? is there a downside to running a too large injector these days? or, would there be an upside to running a smaller injector at higher duty cycle? I can see that there are smaller injectors still available, but the ones i have seen specifically marketed for RB's are pretty large (see: https://golebysparts.au/collections/fuel-rail-injector-kits/products/nissan-rb20-fuel-rail-bosch-980cc-1150cc-injectors-turbosmart-fpr800-regulator-kit), and i dont know enough about them to say one not marketed for RB's would fit or not. I have searched the forums, and amongst all the posts on older tech, I did see gtsboy recommend EV14's, but no size was mentioned... again, i'm not clear on if the smaller size bosch injectors are also EV14's as they do look similar.  also, if someone can recommend a tuner familiar with RB's in the Geelong or West Melbourne area i'd appreciate it. Thanks in advance guys. Cheers, Rowdy  
    • FWIW the depth of the groove in the rubber pad is not super essential, the blocks are rubber and squish a bit. If you are worried an angle grinder will make a deeper groove quick smart
×
×
  • Create New...