Jump to content
SAU Community

Recommended Posts

Does boost build up quicker in say 1st gear and with a slightly larger spike than compared with in 4th gear?

My boost controller is set up at 12psi and on the dyno in 4th gear it shows somethin like 12.5psi at like 3krpm and the tapers off to like 12psi at around 7-8krpm. But then when i run it on the street and take off in 1st gear, i check the peak boost on my profec B spec 2, it reads usually between 13.5-13.8psi.

Is this just an inaccuracy in the boost controller or does it actually spike higher in lower gears?

Link to comment
https://www.sau.com.au/forums/topic/183636-boost-build-vs-gears/
Share on other sites

Higher gears I find generally bring boost on earlier (If say accelerating from 2000RPM) As the turbo has more time to accelerate.

But I generally find that it spikes around a bit more in the lower gears as the boost controller has less time to react to boost spikes.

It also depends on how the boost controller is setup.

yeah it would be a mix of things that determine what it does. in higher gears it can generally build more boost as there is more load, but in low gears the boost can spike so much quicker that it goes higher before the controller knows what's going on.

  • 4 months later...

I have a GCG highflow on the rb25. 15psi is up by about 3500-4000rpm in 2nd then less than 3500rpm in 3rd and 4th.

In 1st though I think I only have 6psi at ~3900rpm and 11psi ~5000rpm.

Is this normal? Anyone with HKS2535 or GCG turbos noticed what there boost is like in 1st. The car is very quick but I reckon the stock turbo is better at <4500rpm in 1st. I think I had 7-8psi by 3500rpm in 1st with the stocker. I guess the load isn't there in 1st so I shouldn't be too tough on it.

Edited by benl1981

My understanding is that boost is pressure the engine isn't ingesting, load is time based as the higher the gear the slower the motor RPM is accelerating (therefore there's an increased resistance to air flow going into the motor)

This combined with the fact your often using more throttle to maintain adequate acceleration in higher gears results in a greater "backlog" of air in front of the motor, meaning more boost and finally more power. Its s viscous cycle 

As others have said Phil, your generally more likely to experience a boost spike in higher gears, not lower, as its these higher airflow / faster boost transient conditions that tax a wastegate and EBC's chances of responding accordingly.

In your post though, your not comparing apples to apples. How does your 4th gear max boost and spiking issue compare to 4th gear on the street?

EDIT: Noticed im talking to a dood who asked a Q 4 months ago - whoops.

Boost in lower gears can be affected by dump, zhaust size, WG flap sealing ability... and most importantly EBC.. are you running one? It's not completely easy to compare your setup to others.

Edited by GeeTR
  • 2 years later...

diggin up and old thread here....

ive got my profec b spec running 13.5psi in my r32 gtr, usual mods aftermarket front pipes, high flow cat, 3.5" cat back, pods..

if i come to a stop, reset Peak Boost, then take off hard in first, go in second gear and take it easy, if i go into Peak boost again it shows it peaked at 14.5ish psi, but the thing is i never see this displayed on the screen ? the screens shows 13.4 -13.6psi

then i did another test, reset peak boost while driving in 4th, drop it down to second and accelerate, then go into 3rd etc then cruise it, peak boost shows 13.5psi...which is good !

so my questions is why does it peak to much in 1st gear ? why isnt it displayed on the screen ? but is saved as "peak boost"??

any info would be great !

probably from boost building much quicker when it first comes on. the profec doesnt react quick enough to stop it spiking 1psi. you could help it by lowering the start boost and gain a little bit but thats gonna make boost build slower in other gears. personally i wouldnt worry, 1psi extra in first isnt gonna make the slightest difference

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • We will review wtf is going on, but if you made any donations let me know and i will follow it up with the admins
    • See, that button sounds like perfection Duncan! My eyes really don't like light shining at them from a dash when I'm driving. Being part red colourblind, I've found for most cars that I can change colours on, I set everything to red, so my eyes see the elast amount of colour! I miss normal gauges in cars
    • bro, knowing the Japanese in  the 90's, i wouldn't be surprised if they shared components across their model lineup.
    • Maaaan so many "little" things  i rly hope my old RB20 would be "ok" and not too bad. I try to learn what and what not do i need. I look at crossmember at it looks different...even parts numbers are different. Wiring and all that i rly do not know...yeah someone mentioned the speedo thing. On that yoke clip. I rly do not know what can and cant be done "custom" so that is why iam asking to know and not be suprised 🙂  I know what it looks like  
    • Oh, there's also the gearbox crossmember which will probably be different between the small box and the big box, and the wiring loom will probably need to be modified, because the plugs for the switches etc, will probably be different. And I think the speedo on the small box R34s is from somwhere stupid, like the diff, possibly, so you'd need to work out what needs to be done about that (assuming it is different). I think the thing you need to realise is that the front end of that yoke is a large hollow tube with splines on the inside that mates with the splines on the box's output shaft. It is a dedicated thing - not available "aftermarket". They were made to suit that box, by the car's OEM.
×
×
  • Create New...