Jump to content
SAU Community

Recommended Posts

Hey guys..

Just got back in my car after its been parked for about 3 hours and had fluid all over the ground.. Id say about as much as a gatorade bottle spilled over the ground..

It seems to be comming from the aircon area, just under the front cabin, however the aircon is off? everytime the car is running it starts to pump out massive amounts of it.. and then slowly seeps out when its stopped.

the fluid is yellowish (like orange juice) in color and slightly oily.. its similar to water so Im assuming it must be the aircon however it has not been on for a fair while.. not since sunday??

I checked all the other fluids and they are at maximum level, it does look similar to radiator fluid and smell similar but the fluid in the radiator is not dropping. The radiator fluid is also orange/brown :S

Should i take it easy and assume its the aircon? never happened before so perhaps the aircon has been blocked?

if anyone could help would be great...

Thanks

Yeah it cools..

The coolant is japanese coolant.. Shipped from japan its red/brown and fades with time.. its only got 8000km on it.

Any way to check the refrigerant?

It slightly smells like coolant, and is slightly oilly.. so im confused why its not the full on smell.. its just very faint..

The fluid is overfilled by the mechanic .. so could it be overflow? why its over flowing now i wouldnt know

Yeah it cools..

The coolant is japanese coolant.. Shipped from japan its red/brown and fades with time.. its only got 8000km on it.

Any way to check the refrigerant?

It slightly smells like coolant, and is slightly oilly.. so im confused why its not the full on smell.. its just very faint..

The fluid is overfilled by the mechanic .. so could it be overflow? why its over flowing now i wouldnt know

Is the car an auto? If it is check your radiator overflow bottle does not have oil sitting on the top. The autos pass their gearbox oil through the bottom tank of the radiator for cooling. If a leak forms inside the tank you will get oil in your water which is likely to spill out into your overflow bottle. Be very afraid!

Its coolant and one of the pipes has let lose.. seems the clamp may have come undone.. lets hope i dont need to replace the silicone piping..

Unfortunately have to drive home.. Now I no I should have got roadside assistance..

Lets just hope I dont run into any problems.. Ill try seal the join with gum or something for a temp fix .. lets hope it works for the time being

hole.jpg

The silicone tubes are located here behind the engine.. anyone know where to find a replacement?

Edited by DECIM8

This is screwed! There was a hole in my pipe which runs off the engine, yes the metal pipe .. about 1-2mm diameter.. I dont know if this part is replaceable..

For the mean time (how its prob been running since i bought it) we cut the hose end off and pushed and clamped over the hole, its holding and I have presure back in the radiator again thankfully.

Anyone got a solution which doesnt involve removing the engine to hot weld it? Anyone got any idea wtf the part is?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was once told, who it was I'm to old to remember, that the length of the OEM wheels brace supplied with a vehicle is designed long enough for a average person to apply enough torque to do up, and undo the wheel nuts to the specified torque  What a average person is is anyone's guess though, i.e. average fat bastard, average knuckle head, average perfect sized human......like me Unless of course, a tyre shop has ugga dugga'd them up to "torque to yeild/strip" specs, used cross threading as natures lock tight, or a big breaker bar was used to tighten them up to get some nice stretch in the poor old wheel studs Me, I torque wheel nuts to 1 elbow joint click, lower torque settings are based of wrist clicks, higher torque settings are based of shoulder clunks, or total dislocation for anything that requires all of the torques 
    • I think the catch can design is pretty flawed. Evident in the fact that the V2 one moved to a larger top mounted filter which alone would have helped with overflow and reduce restrictions compared with the side filter. I also imagine there was a major improvement to the baffling design. It is worth mentioning that this catch can with the RB20 was never as much of an issue and the high kms RB25 is likely a part of the problem. I have gotten quotes for both a new "Vibrant Gen 3" catch can and to modify this existing ones but that may have to wait until after the track day. I hope the sump/head breathers/drains and cam splash plates will be enough
    • Yep, both. The ratio is 1.8 instead of OEM being 1.7. The rocker bodies are modified with a larger bolt hole and re-threaded with 10mm holes instead of the 8mm YT has stock. Finding out they don't actually fit the stock castings cause a lot of un-impressment by the person in the USA who tapped the new holes for the 'upgraded' YT product. He was very unhappy with them given their previous design did not require 'clearancing'
    • That too, but I think this is why she's put the work into the cam cover baffles. I mean, a catch can should only need to be a catch can, not an oil air separator also. Not to say that putting the effort into having it do a better job of oil-air sep is a waste of time, but doing the sep earlier is always going to make life better. And that should happen now anyway.
    • I think both. Higher ratio and more stout. I think at least part of his lift increase came from the rocker.
×
×
  • Create New...