Jump to content
SAU Community

Recommended Posts

This is a Harley Davidson 2005 Softail, its been custom modified from factory and also modified after market.

My father bought it brand new in 2005 for $40,000, and meticulously maintained it. It was his baby.

My parents have gone through a very messy divorce since july 2006, in which my mother took the bike (as it was rego'd in her name but the loan/lease was in my fathers name) Since then my father has been paying the monthly repayments of $650 a month while my old lady has comfortably taken ownership of it at his expense (we could do nothing, very dodgy loophole)

The divorce is set to be finalized on september 17th, part of the agreement was the bike to be sold with the money it is sold for covering the remaining debt on the lease ($20,800). It was up to my old lady to take responsibility to sell the bike but she has made no effort, so now we have taken it into our own hands in a bid to atleast recover the cost of the payout for the lease.

Due to whole lot of dodgyness on behalf of my mother we've basically realized that if we don't do anything about this, she will continue to ride while we pay for it. So we have now got given the go ahead to take it into our own hands to advertise it and buy law of court she will have to accept any offer above $20,800.

Im sure alot of people probably don't understand the situation but take my word for it, we have been royally screwed and wayyy too trusting...

So our loss is someones gain.

You can take this bike for $21,000 just to cover the cost of the lease, even tho the bike should of taken offers around the $30k mark, WE JUST NEED IT GONE ASAP!

2005 softail

200mm rear end

bigger alloy wheels

aftermarket seat

aftermarket air intake

aftermaret exhaust

bike2fp9.jpg

bike3pg3.jpg

bike1ha9.jpg

bike4gz7.jpg

bike5ww2.jpg

Reply via PM if possible and I'll pass your number onto my old man if your serious.

Asking Price: $21000

This is not a negotiable price people.

It is extremely cheap, anyone who thinks otherwise just go take alook on bikepoint or any similar site and watch all the prices for simiar examples to this easily crack over the $30k mark.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The max they would go for me is 50.
    • That cannot have been a fun set of drilling. The stock "baffle" looks identical to rb26, I just cut fuel cell foam to fit the full length under the baffle.
    • I understand your sarcastic exasperation. But to be fair - the baffles do indeed fit OEM cam covers. They did omit to say that you need to do a bunch of stuff. But they do fit them.
    • Got started on the modification to make these splash plates fit over the long weekend. First the surprisingly time consuming task of swapping all the cam cap bolts to Tomei cam cap studs. I did the method of removing one bolt at a time, applying loctite to the stud, double nutting to torque as the manual described. Then carefully unlocking the nuts without disrupting the torque of the stud (and going back to re-torque a few times when it slipped). Finally applying the nut and torquing to spec. Repeat x28 Next up I went about removing the stock cam cover baffle so I could ensure it was fully clean after drilling for stud clearance.  As the blind rivets holding the baffle on were domed I used a punch to mark the center then used 4mm drill bit to carefully drill out the rivet without going too far part the baffle. As seen in other thread here is what is inside the stock baffles I decided on M4x6mm bolts to bolt the baffle plate back on with. I used a 3.3mm drill bit with some tape to mark the depth at ~8mm. Next was to tap the threads using a cheap bunnings kit M4x0.7. With the baffle removed I also drilled out the spot welds holding in the baffle plate oil returns. Unsure whether this was the best option or if I should have cut holes in the Hypertune splash plates to allow the oil drains to still function... time will tell. I then removed the the Hypertune splash plates so I could rest the cam cover on top and use a dab of grease to mark where the studs impacted the oem cam cover baffle. The most obvious spot was on the hump from the stock mesh is held. Using this hole as an anchor I bolted the oem baffle plate back into the cam cover and lined up the Hypertune splash plate. Marked the rest of the holes for the studs and drill those out too. Total 32 holes drilled and 12 threads tapped on the passenger side cam cover alone for this bolt on part that totally clears all OEM cam covers.. Drivers side next as well as some E85 safe fuel foam to fill the space behind the behind cam cover baffle plates. oh and some lock nuts for the splash plates of course.
×
×
  • Create New...