Jump to content
SAU Community

Recommended Posts

That should be fine.

CASTOL EDGE 10w60

SHELL HELIX ULTRA 5w40

The above are also good quality oil's to use.

Have a read of the link below, plenty of recommendations and experiences with different oil's :worship:

http://www.skylinesaustralia.com/forums/in...showtopic=22458

Edited by abu
Link to comment
https://www.sau.com.au/forums/topic/185520-99-r34-gtt-neo/#findComment-3356745
Share on other sites

if the engine is in good condition and doesn't "breath", then you want the thinnest oil you can get away with.

the first part of the oil numbers (0w40) is it's grade when cold.

so 0 is as thin as you can get which is good.

get him to check after a few weeks of driving and then again a month after to see if it is using up any oil.

if it is, then it's too thin and will need to top up until the next oil change where he should try something else..

perhaps with a 5w or 10w

the usual Castrol 10w60 recommendation is good on the usual 12+ year old engine which will have some wear.

so the thicker oil won't get burnt up in the combustion process.

there are also good threads regarding synthetic, semi synthetic oils which you can find on these forums.

Link to comment
https://www.sau.com.au/forums/topic/185520-99-r34-gtt-neo/#findComment-3356927
Share on other sites

if the engine is in good condition and doesn't "breath", then you want the thinnest oil you can get away with.

the first part of the oil numbers (0w40) is it's grade when cold.

so 0 is as thin as you can get which is good.

get him to check after a few weeks of driving and then again a month after to see if it is using up any oil.

if it is, then it's too thin and will need to top up until the next oil change where he should try something else..

perhaps with a 5w or 10w

the usual Castrol 10w60 recommendation is good on the usual 12+ year old engine which will have some wear.

so the thicker oil won't get burnt up in the combustion process.

there are also good threads regarding synthetic, semi synthetic oils which you can find on these forums.

thanks dude, yeah i know about the specs of oil, he was just unsure whether maybe that was too thin for it or not. i mite tell him to try the shell ultra which i think is a 5w-40

Link to comment
https://www.sau.com.au/forums/topic/185520-99-r34-gtt-neo/#findComment-3356954
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...