Jump to content
SAU Community

Recommended Posts

Probably not. Says "Owners Manual" not "Service manual". I'd have to have a look at whats in it before I'm prepared to buy one. I'm not sure I even need an owners manual.

Yep, original request to those guys was the full workshop manual back in 2008 (http://www.skylinesaustralia.com/forums/topic/232599-translated-workshop-manual-m35-c34/ )

Also, it states for 2001-2007 Stagea, but no mention of VQ35de? WTF?

I know the answer is here but I can't find it in a rush.

Attessa system fluid - same as the transmission?

Glad I'm not the only one that struggles to find anything.

90 pages of 'info' is more like 'comment on stuff about the M35.'

:rolleyes::ph34r:

To those who've rewired their fuel pump, where did you run the wiring from the battery into the cabin?

I was looking at it today and thinking the easiest way would be to drill a hole in the side of the duct where the cabin air filter is, and put a rubber grommet in. Most obvious place anyway...

Just slide it throug the main wiring grommet, behind the battery, then down the passenger side and along the back seat.

I've got so much stuff going thru there that I've left a permanent draw wire.

  • 2 weeks later...

Thinking about how I'm getting the Fcon tuned, and more and more I'm thinking I should just go 98 for now. E85 isn't plentiful enough, 98 would just be easier.

If I go that way, I'm already changing the fuel pump and filter, and I've got the wideband.

Would I still need to change the injectors and/or fit a FPR for a 98 tune running the standard turbo?

I can't see you needing bigger injectors with the stock turbo. From what it seems, if you run ~20psi on stock turbo it will die quick ish.

If you tune with the stock boost (allowing extra 1-2psi for exhaust upgrade) it would need the rich factory set AFR leaned out a tad so the injectors should be fine.

Edited by slippylotion

^^^ what Paul said.

Thinking about how I'm getting the Fcon tuned, and more and more I'm thinking I should just go 98 for now. E85 isn't plentiful enough, 98 would just be easier.

If I go that way, I'm already changing the fuel pump and filter, and I've got the wideband.

Would I still need to change the injectors and/or fit a FPR for a 98 tune running the standard turbo?

As soon as you go the full hog on you intake pipe you will have a top end lean problem with standard injectors & fuel pump. Andy got good results (AFRs richened up nicely) just by changing the fuel pump. My injectors are providing enough fuel just by changing fuel pressure regulator (stock pump). So if you planned to do either of those, & you've already got the pump, then you'll be fine.

I'm of the belief that our standard injectors can be sufficient up to maybe 250kw or more), given a bit of extra pressure to increase the flow. Check out 'injectors online' to see what sizes are used in various factory applications. eg according to that website, Gen III 5.7lt motor uses 260cc, XR6 (including turbo) use 295cc. M35s are 370cc, & when given extra pressure (there's a formula around somewhere) they can flow in the vicinity of 440cc/min.

^^^ what Paul said.

As soon as you go the full hog on you intake pipe you will have a top end lean problem with standard injectors & fuel pump. Andy got good results (AFRs richened up nicely) just by changing the fuel pump. My injectors are providing enough fuel just by changing fuel pressure regulator (stock pump). So if you planned to do either of those, & you've already got the pump, then you'll be fine.

I'm of the belief that our standard injectors can be sufficient up to maybe 250kw or more), given a bit of extra pressure to increase the flow. Check out 'injectors online' to see what sizes are used in various factory applications. eg according to that website, Gen III 5.7lt motor uses 260cc, XR6 (including turbo) use 295cc. M35s are 370cc, & when given extra pressure (there's a formula around somewhere) they can flow in the vicinity of 440cc/min.

I would agree with you on the injectors Leon as even at 18PSI with my car my Wideband never gets over 10.8 unless under load going up a hill then is gets to 11.1. However the AFM is well and truly maxed giving readings of 5+...and I know my duty cycle is over 95% at times....I have also seen 100% quite a bit......I can live with that on the street as I am hardly ever up it.

However I would never track it without bigger injectors and the AFM clamped.

P.S. I think its awesome how the car has worked out its tune with the extra pressure at 14v with the Walbro on mine....it would be very interesting to try a set of 440cc injectors in the car with the standard fuel pump to see if/how it runs.

However I would never track it without bigger injectors and the AFM clamped.

P.S. I think its awesome how the car has worked out its tune with the extra pressure at 14v with the Walbro on mine....it would be very interesting to try a set of 440cc injectors in the car with the standard fuel pump to see if/how it runs.

Well that's kind of my plan. Do pump and get tune with MAP sensor.

Will that cause an issue if I do some track work?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
×
×
  • Create New...