Jump to content
SAU Community

Recommended Posts

ok guys, Ive been working on this for a couple weeks now(dont have much time thanks to the us army..) and am having abit of trouble tracking down this fuel issue. the engine is an rb20det from a cefiro. seems to be having a fuel issue. the old saying too much is never enough is apparently not true here. usually at low rpms, it bogs down, with black smoke and horrible fuel mileage. Ive replaced the fuel filter, FPR, checked fuel pressure, replaced plugs gapped properly, cleaned the maf, checked for intercooler leaks and vacuum leaks and couldnt seem to find any. I searched here and found some people with some of the same issues and the solution was to clean up the aac. I did that and it seemed to help alittle(it doesnt buck hard like it used to now). but it still shoots out black smoke every now and then(mostly at low rpms as mentioned) Power is lacking as well obviously. shooting flames when I downshift as well, which looks slightly cool, but obviously not supposed to do that.

now the only things i can thing of that are left is maybe a faulty fuel injector(maybe sticking open?) or the maf has just completely crapped out on me. when you unplug the maf and start the car, it runs idles even worse, and when connected, it idles better so im not sure if the maf is bad or not. i have yet to hook up a 12v sourse and and hook up a volt meter and see what output is. sorry for the long post Im just trying to be as detailed as possible. here are my mods if this helps. any help is greatly appricated.

RB20DET(from A31 Cerfio if i remember correctly)

ARP Head Studs,

GReddy 1.2mm Head Gasket,

GReddy Timing belt,

Fidanza adjustable cam gears,

Hybrid FMIC and piping,

Turbo XS BOV,

HKS pod filter,

3" exhaust with Fujitsubo NGK axle back,

GTR fuel pump,

Koyo radiator w/ dual 12" fans,

GReddy EManage,

GReddy Profec E-01,

GReddy Auto Timer,

unplugged the 02 sensor, didnt seem to make any differance in the idle at all. bad 02 sensor?

No, usually when the O2 sensor plays up it results in an erratic idle (hunting) but stabilises once the O2 sensor is disconnected (presumably no longer in closed loop mode).

Have you inspected the plugs and are they all the same (presumably very black)? Usually fouled plugs will eventually clear themselves especially after a long run (eg down the highway).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Duh... to answer my own silly question, it's actually described in the FSM... ...400 pages away at the end of the manual, for RB25DE/DET signal descriptions, it cites the TPSwitch signal action, is dependent on the TPSensor value ~ this tends to infer the builtin POT voltage signal is the primary, and the switches are fallback/secondary should the POT fail/TPSensor signal lost (and switch alone with no TPSensor signal allows for base idle speed setting).... makes sense... they (TPS units) used to fail/wear the POT with time, they're not exactly built to last ~ having the switch as a redundancy gets around this...(or, it's less likely both signals would be lost as they're on different power rails)... and of course wrt RB26DETT, you have to electrically disconnect the IACV solenoid from the harness, to defeat idle air control...  
    • Dose is unaware just how much fun 145-150kw would be in a 2.5L NC MX5. It would be one of the most fun things to drive to ever grace SAU.
    • Same thought crossed my mind ~ depends on how one connotes 'stalling'...ie; gets a rough/stumbling idle as it get warm until it stalls... or... idles ok and simply falls-over when it gets to temp... ...you can test the whole circuit with a couple of resistors ...unplug coolant temp sensor, bridge terminals with a 2K7 resistor (ECU will do cold start), or with engine warm bridge with a 330R resistor (ECU will consider engine to be at normal operating temp)...it's a quick way to check wiring integrity/ECU response when you don't have a multimeter handy ...
    • They also make them with the motor mounted on the side 
    • Just be warned that that turbo will not be a direct re-fit to the car. The exhaust housing is, of course, in the same place. It has to be - it's bolted to the exhaust manifold. So the dump will fit up. But the centre housing is not as long, so the comp housing will move backwards. This will affect both the turbo inlet and the outlet. There is fab work that needs to be done. Yes. it has one, it should have one. Paper gasket.
×
×
  • Create New...