Jump to content
SAU Community

R32 Ls1 Conversion


BezerkR32

Recommended Posts

wow. i just read this thread from the VERY start to the end. amazing i take my hat off to you sir.

sorry to be a pain and ask but from what i gather if you don't plan on ripping everything apart, in a way its fairly straight forward? the wiring and exhaust of cause have their issues but other people deal with those problems and you encountered some problems when you went with the trumpets? i assume these would have been removed if you left the standard intake on?

The only thing i could bring it down to was the steering and brackets for mounting?

Without making everyone read through the whole thread (as amazing as it is) can you give a basic list on whats needed?

Link to comment
Share on other sites

  • Replies 812
  • Created
  • Last Reply

Top Posters In This Topic

basically, if you were going to leave the engine standard and rego.

1) Fabricate engine mounts.

2) fit steering rack that will fit still encorporating power steer or run a manual rack. Rack ends to suit.

3) Transmission Crossmember

4) Tailshaft

5) Exhaust including modified extractors.

6) R33 clutch master cylinder bored one size oversize.

7) Radiator hoses (could use standard radiator) Thermo Fan

8) Throttle cable

9) Speed sensor compatibillity?

10) Misc plumbing e.g heater, booster, intake, air, steer. etc

11) Wiring

12) Modify fuel system (no return line) Reg intank.

these are the main points i can think of off the top of my head.

all conversions are similar, this one did not require things like crossmember, sump or trans tunnel mods which was good. and its a tidy fit, easy to change plugs and remove gearbox.

wow. i just read this thread from the VERY start to the end. amazing i take my hat off to you sir.

sorry to be a pain and ask but from what i gather if you don't plan on ripping everything apart, in a way its fairly straight forward? the wiring and exhaust of cause have their issues but other people deal with those problems and you encountered some problems when you went with the trumpets? i assume these would have been removed if you left the standard intake on?

The only thing i could bring it down to was the steering and brackets for mounting?

Without making everyone read through the whole thread (as amazing as it is) can you give a basic list on whats needed?

Link to comment
Share on other sites

Thanks heaps for that the only other question i had and i might get pulled up here is that do you think the conversion (apart from the power outsings) would be relatively the same with just a 5ltr engine instead of the 5.7 im just weighing up all options here

Thanks heaps

Link to comment
Share on other sites

Supercharged 6 would give less room I reckon. the V6 is not much more compact than the 8 and the you add the supercharger (and cooler if you want etc). also depends on the type of blower you use. and what 6 would you use? cause the old holden 6 is absolute crap. and buy the time you buy the 6, trans, blower etc it would probably cost more then the LS 5.7 and make less power. waste of time.

Link to comment
Share on other sites

yeh i agree, the 5.0s are a cast iron boat anchor. 165kw. and not sure why you would condider a v6 conversion when you can bolt a turbo'd RB straight in.

Supercharged 6 would give less room I reckon. the V6 is not much more compact than the 8 and the you add the supercharger (and cooler if you want etc). also depends on the type of blower you use. and what 6 would you use? cause the old holden 6 is absolute crap. and buy the time you buy the 6, trans, blower etc it would probably cost more then the LS 5.7 and make less power. waste of time.
Link to comment
Share on other sites

Yeah, agreed on the V6 thing too. I hate the holden 6's, I think they're crap and I wouldn't waste my time on one.

Not sure what they weigh, but I dare say with all the ancillaries it'd be more than the LS1, or close enough to.

Link to comment
Share on other sites

the eco-tech is still cast iron so it would be at least 60kg heavier, the alloytech in the vz onwards would be lighter.

Yeah, agreed on the V6 thing too. I hate the holden 6's, I think they're crap and I wouldn't waste my time on one.

Not sure what they weigh, but I dare say with all the ancillaries it'd be more than the LS1, or close enough to.

Link to comment
Share on other sites

ill see how the tremec goes next friday.

Going up to Unigroup in the morning to finish up the tune. Ill try to get more video of decent quality this time.

But what is a decent box that you can put behind the chevs. The ZF etc 6 spds are not exaclt slick things. I have found the motor i want for my car, but cant find a gearbox :down:
Link to comment
Share on other sites

yeh, probably should keep both hands on the wheel instead of one out the window ya noob.....my arse hole got so tight when you were heading towards the concrete........rofl

Suuuuuummmmerrrrrnnaaaaaattttssss!!!!

lol!

Link to comment
Share on other sites

yeh, probably should keep both hands on the wheel instead of one out the window ya noob.....my arse hole got so tight when you were heading towards the concrete........rofl

Must have been a pleasant change for you?!

Link to comment
Share on other sites

what.......surely one of your cars is going.

lol surely you knew drag boy wouldn't know what to do when the corners arrived.

is it all go for FRiday? Looks like mine has missed 0ot again :)

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



×
×
  • Create New...