Jump to content
SAU Community

Recommended Posts

wow. i just read this thread from the VERY start to the end. amazing i take my hat off to you sir.

sorry to be a pain and ask but from what i gather if you don't plan on ripping everything apart, in a way its fairly straight forward? the wiring and exhaust of cause have their issues but other people deal with those problems and you encountered some problems when you went with the trumpets? i assume these would have been removed if you left the standard intake on?

The only thing i could bring it down to was the steering and brackets for mounting?

Without making everyone read through the whole thread (as amazing as it is) can you give a basic list on whats needed?

  • Replies 812
  • Created
  • Last Reply

Top Posters In This Topic

basically, if you were going to leave the engine standard and rego.

1) Fabricate engine mounts.

2) fit steering rack that will fit still encorporating power steer or run a manual rack. Rack ends to suit.

3) Transmission Crossmember

4) Tailshaft

5) Exhaust including modified extractors.

6) R33 clutch master cylinder bored one size oversize.

7) Radiator hoses (could use standard radiator) Thermo Fan

8) Throttle cable

9) Speed sensor compatibillity?

10) Misc plumbing e.g heater, booster, intake, air, steer. etc

11) Wiring

12) Modify fuel system (no return line) Reg intank.

these are the main points i can think of off the top of my head.

all conversions are similar, this one did not require things like crossmember, sump or trans tunnel mods which was good. and its a tidy fit, easy to change plugs and remove gearbox.

wow. i just read this thread from the VERY start to the end. amazing i take my hat off to you sir.

sorry to be a pain and ask but from what i gather if you don't plan on ripping everything apart, in a way its fairly straight forward? the wiring and exhaust of cause have their issues but other people deal with those problems and you encountered some problems when you went with the trumpets? i assume these would have been removed if you left the standard intake on?

The only thing i could bring it down to was the steering and brackets for mounting?

Without making everyone read through the whole thread (as amazing as it is) can you give a basic list on whats needed?

Thanks heaps for that the only other question i had and i might get pulled up here is that do you think the conversion (apart from the power outsings) would be relatively the same with just a 5ltr engine instead of the 5.7 im just weighing up all options here

Thanks heaps

Supercharged 6 would give less room I reckon. the V6 is not much more compact than the 8 and the you add the supercharger (and cooler if you want etc). also depends on the type of blower you use. and what 6 would you use? cause the old holden 6 is absolute crap. and buy the time you buy the 6, trans, blower etc it would probably cost more then the LS 5.7 and make less power. waste of time.

yeh i agree, the 5.0s are a cast iron boat anchor. 165kw. and not sure why you would condider a v6 conversion when you can bolt a turbo'd RB straight in.

Supercharged 6 would give less room I reckon. the V6 is not much more compact than the 8 and the you add the supercharger (and cooler if you want etc). also depends on the type of blower you use. and what 6 would you use? cause the old holden 6 is absolute crap. and buy the time you buy the 6, trans, blower etc it would probably cost more then the LS 5.7 and make less power. waste of time.

Yeah, agreed on the V6 thing too. I hate the holden 6's, I think they're crap and I wouldn't waste my time on one.

Not sure what they weigh, but I dare say with all the ancillaries it'd be more than the LS1, or close enough to.

the eco-tech is still cast iron so it would be at least 60kg heavier, the alloytech in the vz onwards would be lighter.

Yeah, agreed on the V6 thing too. I hate the holden 6's, I think they're crap and I wouldn't waste my time on one.

Not sure what they weigh, but I dare say with all the ancillaries it'd be more than the LS1, or close enough to.

ill see how the tremec goes next friday.

Going up to Unigroup in the morning to finish up the tune. Ill try to get more video of decent quality this time.

But what is a decent box that you can put behind the chevs. The ZF etc 6 spds are not exaclt slick things. I have found the motor i want for my car, but cant find a gearbox :down:

yeh, probably should keep both hands on the wheel instead of one out the window ya noob.....my arse hole got so tight when you were heading towards the concrete........rofl

Suuuuuummmmerrrrrnnaaaaaattttssss!!!!

lol!

yeh, probably should keep both hands on the wheel instead of one out the window ya noob.....my arse hole got so tight when you were heading towards the concrete........rofl

Must have been a pleasant change for you?!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
×
×
  • Create New...