Jump to content
SAU Community

Recommended Posts

i just got a r33 gearbox with blitz twin plate clutch put into my 32 and now when i drive through the gears my car tends to fall back into neutral without even pressing on the clutch and also my steering goes stiff hard after bout 2 mins of driving it gets kinda annoyin cause i hav to constantly hold the gearstick in one hand and try and steer with the other any help would be apreciated

post-17770-1191493479_thumb.jpg

I had Nissan Pulsar Q (the SR20 model) and it would always pop out of 5th gear. The box wasn't f**ked, had to replace something though that cost about $300 from memory.. have no idea what it was, going back a few years now when I had little interest in cars. If yours is doing it in all gears though you could be in trouble. Where'd you get the box from? I'd say give a mechanic a call.

i just got a r33 gearbox with blitz twin plate clutch put into my 32 and now when i drive through the gears my car tends to fall back into neutral without even pressing on the clutch and also my steering goes stiff hard after bout 2 mins of driving it gets kinda annoyin cause i hav to constantly hold the gearstick in one hand and try and steer with the other any help would be apreciated

the steering is related to a hicas error. most likely the hicas computer isn't receiving a speed signal.

i just got a r33 gearbox with blitz twin plate clutch put into my 32 and now when i drive through the gears my car tends to fall back into neutral without even pressing on the clutch and also my steering goes stiff hard after bout 2 mins of driving it gets kinda annoyin cause i hav to constantly hold the gearstick in one hand and try and steer with the other any help would be apreciated

Hi,

Common problem.. are you sure you don't have the rubber boot around the wrong way? Puzzled me for ages...

  • 11 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it's for a SR20, make sure it's not the American Poncams, might as well call them Poocams. Had a set in a friend's car, all scuffed up after a few track days. Like the metallurgy Tomei USA used is junk. Went back to JDM OG Tomei Poncams, no issues till now.   Tomei USA is not the real OG Tomei.   Random rant over, fk the US of A, bunch of c u n t s. 
    • Most of the industry in North America either runs on Siemens or Allen Bradley. I have two redundant S7-1500's on my desk right next to me for simulation. Siemens has been losing ground though since Stuxnet, as cybersecurity is a big thing. In my line of work that is federally regulated, you must by law have a cybersecurity management program in place and its audited and inspected every so often.  I work with Emerson PLC's daily (RX3i's) and have done large biogas/refinery projects with their DCS's. Their PLC's are somewhat OK minus the way they do PLC redundancy (You have to download on both PLC's separately every time you make a change )  As for their DCS's... you'll be limited financially first before anything else stops you. Costs are exorbiant at roughly 10x what it would cost you to do with any other system (e.g AB PAC).  1990's, those suckers are brand new haha! Kraft-Heinz (An old client when I use to work for an ESP) still runs Siemens TI505 PLC's from the mid 80's. Ohh how I don't miss working with those... you could only do a certain number of online downloads until it's "Change" buffer would be full and you would then need to go offline to do a full download. There was no warning of when this was coming up and it generally would happen when you would go in at 2am to make changes before production -_-.     
    • Unfortunately, not only is that not the case, one of the main "Selling points" of safety over comms is they clearly state in writing that there's no need to segregate safety networks from non-safety networks. It always gets intermingled with everything else on an ICS/OT network. 
    • Hello. I have an a31 cefiro but since I am in Turkey we have a CA20S engine. I did some research. Then I found that I can swap with a ca18 but when I heard that it has the similar substructure as the s13. I thought I can swap with an sr20 because the sr20 was used with the s13. So can I easily swap the sr20 on my cefiro or is it difficult? 
×
×
  • Create New...