Jump to content
SAU Community

Recommended Posts

I haven't taken my car to the track yet and i am just woundering what pads i should use.

i would just be putting them in driving to the track going for a run and taking the pads out again once i got home.

I have a solid (vented)front rotor and drilled rears. I will get slotted rotters for the car in time but untill then i will stay with the setup the last owner had.

Its a r32 GTR.

Also after the best tyres for the track and where to get them?

and can you run semi slicks on just the wakefield licence.

Cheers

Keith

Edited by BNR32t
Link to comment
https://www.sau.com.au/forums/topic/188200-brake-pads-for-the-track/
Share on other sites

I haven't taken my car to the track yet and i am just woundering what pads i should use.

i would just be putting them in driving to the track going for a run and taking the pads out again once i got home.

I have a solid (vented)front rotor and drilled rears. I will get slotted rotters for the car in time but untill then i will stay with the setup the last owner had.

Its a r32 GTR.

Also after the best tyres for the track and where to get them?

and can you run semi slicks on just the wakefield licence.

Cheers

Keith

I will probably be going for the EBC red's for everyday use and track (designd for the track as they need to heat up to be most effective). Are you looking at changing the rotors as well? You normally let the pads bed in to the rotors and swapping and changing them would seem to limit their effectiveness.

I'm still considering tyres, Ladybytes swears by here Federal 595 RS's.

The wakefield licence allows you to run full slicks if you want.

I will probably be going for the EBC red's for everyday use and track (designd for the track as they need to heat up to be most effective). Are you looking at changing the rotors as well? You normally let the pads bed in to the rotors and swapping and changing them would seem to limit their effectiveness.

I just had these installed last week along with some new RDA rotors. You're sure as hell right in that they need to be warmed up to be at their best.

I've got EBC reds. Yep you need to dig into them a bit when not really warm to stop fast. I'm very happy with their stopping power in general in combination with my RDA front slotted rotors and about to try them on the track. They are half worn already, so we'll see :( My mechanic says the EBC Greens are even more track oriented and need to be warmed up even more!

Edited by sl33py
My mechanic says the EBC Greens are even more track oriented and need to be warmed up even more!

Your mechanic is wrong then :( the greens are a "performance" steet pad. the EBC Red's are more of a "high performance" street/Track. I ran RB74's on wakefield and although some people say they are not as good as some other brands when you way up the $$$ vs performance i thought they did bloody well, no break fade or anything like that

I just had these installed last week along with some new RDA rotors. You're sure as hell right in that they need to be warmed up to be at their best.

They still break as well as ordinary pads when cold? Just lots better when warm?

It normally takes 500km to get the pads and the rotors to bond most effectively. Hopefully it will improve over time?

It normally takes 500km to get the pads and the rotors to bond most effectively. Hopefully it will improve over time?

Yeah hopefully they eventually stop squealing loud enough to wake the dead after 500kms!

What are the ferodo's like everyday?

Or are they just a track pad?

im still using them on my car and they've been on the car for a year and a half! (done 3 full track days on them). they are great on the street. they take about 2-3 normal braking applications to warm up and work effectively, but once you've done that, they're perfect. as an everyday pad, i would recommend them.

as for the track, they are also great. they can handle big temps and wont fade (in my experience anyway). i warped my brake discs before my brakes faded, then my fluid boiled, but the pads stayed true and still to this day will stop my car on a dime....

will is ds2500 the part number? Will they go straite into my r32 standard rotors? Or will i need a different part number?

Cheers Frink, Cause i work at repco and we sell ferodo's so it might be a cheap option for me.

thanks heaps mate.

For Brakes I would go for Bendix Ultimate, they're great for everyday driving, takes about 2 good stops for them to get good "bite", I used them at Texikhana recently and had no fade, sqeal, grinding or excess heat... They were great.

For tyres - street legal semi slicks go for Federal 595RS, best bang for your buck tyre available.

will is ds2500 the part number? Will they go straite into my r32 standard rotors? Or will i need a different part number?

Cheers Frink, Cause i work at repco and we sell ferodo's so it might be a cheap option for me.

thanks heaps mate.

they should do straight in the rotor, they do for 33's. you should be able to research the part number in the cataloge you should have behind the desk (im only guessing...). they are more expensive then the Bendix Ultimates, but i think its worth it....

its funny, just as i say all these good things about these pads, only this morning they ran out pad and i now need new ones! oh well, they're still a great pad....

I'm now considering EBC yellows, better in all ways to the reds except for dust. Not so sure on the quietness though, they don't advertise that.

Considering I can land a full set (F+R) for the GTR for $330, that is a huge saving.

you will find the EBC yellows are more of a track pad than the reds, if its for everyday street use even EBC recommend against going the yellows over the reds.

edit: makes more sense now.

Edited by TiTAN

EBC says:

Ultra high friction pads for race use but perfectly safe for street use (Formula 1846).

Although a full race material and capable of high temperature use with very good wear life, this new formulation sets a new trend in race type brake pad compounds that can be used on the highway. The “bite” from cold is superb which is uncommon with race materials (normally requiring warm-up) and makes this a pad which can be safely used on both street and track. This new formulation has been used by numerous championship race and rally drivers and is truly a milestone in brake pad material development. Nominal friction coefficient 0.5 with zero rotor damage and similar dust to original pads.

http://www.ebcbrakes.com/yellowstuffinfo.html

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh bugger ! Your right ! Good old hydrogen sulfide. Takes me back to the good old school days ! 
    • I've owned a few scooters over the years, a Vespa PX oil burner was my first scooter, followed by a few others, including a little 50cc BeeWee that I used as a barracks bike, and I've had a blast on all of them, they really are the cheapest for of city/suburb transport around The only issue with scooters in Australia is lots of people look down on them due to their size,  maybe they need a big bike to make up for something else where they are lacking, unlike Europe and Asia where every man an their dog owns one, and now that filtering is legal in NSW, local traffic is never a issue Not to say I haven't owned my share of big cc bikes over the years, but they were for more blasting through the hills or Hwy riding where it needed to sit on Hwy speeds Safety wise, I ride like everyone is always trying to kill me, everyone is running a red, or running stop/give way signs, or generally asleep at the wheel, which most people are duringtheir commute, I also ride really safe, and give myself, and everyone else enough room in case I need to pull some hasty evasive actions, I've done a few rider training days over the years, which has come in handy on more than a few occasions  As for mods, there's nothing really, and yes your right about aftermarket exhaust, all you get is loud and obnoxious noises from them, like every 250-300 cc you hear with a aftermarket muffler, in saying this I did put a rear muffler from a 125 Aprilla on one of my old 125 scooters, it was horrendous and no amount of full face helmet and ear plugs would dampen that noise As for coming from the Harley, and what a overpriced POS that was, I no longer do big rides as my poor old busted joints ache after about 1/2 an hour of riding, long cruises are so much more enjoyable now in a car, so a big bike would be pointless   
    • Oh wow, it's easy to forget how cheap these can be. Probably the cheapest way to travel. Though people in cars here tend to be morons and I would not feel very safe. Were scooters ever big in Australia? It used to be the thing growing up in Europe ~20 years ago. 50/70/125ccm Peugeot or Yamaha and some others. Utterly obnoxious Polini race exhausts. Kick stands that slant as much as possible. So loud. So much noise for really not moving very fast at all. But it felt cool at the time. Not sure where I'm going with this, but there is an aftermarket for mopeds! Though I'd have pictured you more for a Goldwing kind of guy after growing out of the Harley.
    • You need to know I am sorry for this.  
    • As the MX5 isn't apparently "manly" enough, and I need something for runs to the local shops, and also take to my part time job at the salon, basically I can keep the MX5 away from car parks and stuff......like "flying lockers", I was wondering what I could buy to fix this issue LOL, I pick up a new Yamaha 125 Delight this arvo from Trooper Lu, basically a R1 that you can fit a slab of beer on between your feet, also, it was $29400 cheaper than a R1, so actually it's 2 x better than a R1    
×
×
  • Create New...