Jump to content
SAU Community

The Sa Wasteland

Cubes

By Cubes,
in South Australia

 Share

Recommended Posts

ANGRYMANR33 Collaborator

ANGRYMANR33

Posted
Posted
i like skylines wooooo

lol, i am never attempting to put an aftermarket rear bar on again.

thing p*ss*s me off so much, and now i cant get my bloody side pods bak on.

who wants to spray my rear bar midnight blue and install it for me??????

what brand is it sometimes u get what u pay for with the cheaper ones if its a good brand u should have minimal problems >_<

Link to comment
Share on other sites
  • Replies 36k
  • Created
  • Last Reply

Top Posters In This Topic

  • Damo_R34

    2820

  • scandyflick

    2266

  • Madaz

    1919

  • craig R33

    1717

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Ryanrb25
Ryanrb25

i went for a hills run last night in the 31 with the roads very slippery.....was much fun. Had to bed in the bottom end bearings so yea..took it for a strap.

DSTROY
DSTROY

Hey Ryan, do you know how to fit a set of drop spindles to the front of a hilux???

Madaz
Madaz

Dam straight Damo would rather do SAU them heroin gts4 are 4.1 because they share the same parts from the gtr i think r32 gtst is 4.3 because of the lack of torque from the rb20

Posted Images

Damo_R34 Grand Master

Damo_R34

Posted
Posted

Might just take it to an exhaust shop and get them to fit it for me. That way i know if they snap a bolt, they fix it. I on the otehr hand, dont have the tools to fix anything major.

Link to comment
Share on other sites
SLED Grand Master

SLED

Posted
Posted
^^ im told for stubborn bolts Anti Freeze

Pffft, thats amateur Steve, I suppose you use spanners too :)

I pull whole engines apart with a club hammer & cold chisel >_<

Link to comment
Share on other sites
D_Stirls Veteran

D_Stirls

Posted
Posted
Just bitching about my unproductive day. Me and Jenkies decide today is that day to put my new intercooler and dump pipe on. Front bar comes off easy as, no problems. Bit of trouble trying to get the stock cooler off.

Decide to have a break before we take it off. glance over to my intercooler box, peel back a bit of packing tape and see "R33 Kit". well now, thats not what i ordered?

so anyway, put everything back together, make sure all bolts are on. ok time for dump pipe.

or, not.

nuts have seized, no chance in hell of getting them off.

so for just under 5 hours of labour, we accomplised:

- found one nut on the cat was really loose, tightened.

- removed thermo fan so cooler core will fit.

lesson for today. pay someone to do it for you.

I'm pretty sure that R32/33/34 intercooler kits are interchangeable as most of them use the factory hot pipe side of the piping and for the cold side you have to cut a hole so there won't be a problem there with lining up as well. Better pull it all back off again.

Link to comment
Share on other sites
JDM032 Experienced

JDM032

Posted
Posted
Might just take it to an exhaust shop and get them to fit it for me. That way i know if they snap a bolt, they fix it. I on the otehr hand, dont have the tools to fix anything major.

no dont coz they will make u pay for the snapped stud.

i have tried that wen i wanted my screamer on and they said nothing about it n i mentioned that sum of the nuts mite be tight n they said if it snaps it not there fault and u have to pay to get it removed.

and if nothing is mentioned about it they will still make u pay! it sucks but they class it as not there fault because they are just doing wat you asked them to do.

Link to comment
Share on other sites
Damo_R34 Grand Master

Damo_R34

Posted
Posted
I'm pretty sure that R32/33/34 intercooler kits are interchangeable as most of them use the factory hot pipe side of the piping and for the cold side you have to cut a hole so there won't be a problem there with lining up as well. Better pull it all back off again.

Yeah but the mounting brackets that were supplied wont fit.

Link to comment
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      It's basically the same platform, hence why everything bolts to everything else Kelford camshafts were recommended by Mania after they asked me what I want the car for, I said "I'll thrash it around daily and maybe take it to the track for fun" 🤣 Factory NC 2.0L cam specs: - Adv. Dur. 256 /256 - Dur @ .050 205 /190 - Lift 9.42mm/8.13mm So, as I know nothing about cam specs, all I can say is the numbers are different and it should get a little bit of lope....🤣
    • Dose Pipe Sutututu
      Best chassis for motorsport use

      By Dose Pipe Sutututu · Posted

      Depends on how extreme, however if you look at SMSP, they're all dominated by Hondas and M cars on amateur/street car events. 
    • MBS206
      Is this pressure plate warped? And do I need a new one?

      By MBS206 · Posted

      Without better pictures, it won't be possible for anyone to work it out further than we have.   Start measuring, EVERYTHING. Thickness of flywheel, and all around it. You want to know is if everything parallel. If from the face of the pressure plate (that bolts to the flywheel) if it is parallel to the pressure plate face, then something is NOT parallel or equal elsewhere. Or you've bent the shit out of the fingers in the pressure plate.
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      Finally getting around to changing whole cold side. (Look at that sludge) lets see where this leads once it’s all together tomorrow.
    • MBS206
      MLR's Bogan cruise ship

      By MBS206 · Posted

      0.5L sounds like nothing. But when it's a 25% increase in displacement, to a newer engine platform, and getting some speedy bits, it should be good!   Compared to stock cams for the 2.5L, are these new cams mainly more lift, or more duration too (shifting the torque curve into higher RPM)?
×
×
  • Create New...