Jump to content
SAU Community

Recommended Posts

Thats weird about the AFM, I was under the impression they flowed well and only really need changing when going for big power as the tuning resolution is a better with a Z32 item. Mine's only running about 180@wheels anyway, and I need to get the sus/chassis sorted before I need anymore :(

Mine was maxed a little over 180rwkw as well as another mates.

Perfectly normal. You can tune them up to around 220rwkw odd but its a fairly rough tune. Essentially when the afm max's out you push in enough fuel at that load point to handle the boost being run. So what occurs is say its tuned for 15psi but the afm max's out at 12psi when it hits 12psi it runs the ignition timing and enough fuel for 15psi so not optimal.

But really you never try (thats if you were good enough to be able to do it) to hold 12psi at part throttle with the afm only just maxing out so usually it goes unnoticed. :(

The Z32 allows for a fair bit more scope. Mine went from maxing the std afm out to ~4.2-4.3v on the Z32. Then ~268rwkw was ~4.7volts and now 302rwkw is high 4.9volts on occasions flat 5volts on those cold nights. So nearing its limits again. :S

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeah 98 for me, and 6.7/100 was my actual usage. On the downside the bloody thing still isn't running properly but at least they hybrid system is happy now. It starts but missfires like a bastard, and isn't throwing any code except "missfire". Thanks scoop. I did notice the AFMs are reading quite different at idle 1.33v and 1.67v so 25% variance (and have both changed and swapped them, the issue stays on the driver's side afm) so I'm looking for exhaust restriction (mouse nest?), compression issue or (hopefully not, no physical damage seen) wiring issue. Throttle might also be an issue but that is harder because you can't swap them side to side and not cheap to fire the parts cannon at.
    • I hope you're right and it somehow justifies it's existence!
    • actually, I've had one of those for a while and it gets more use than you'd think. Yes catching subframes, engines etc coming out under a car on a hoist, but also getting heavy stuff on shelving (to a certain height) without a forklift, holding the fuga's hybrid battery....like many good tools you'll find the jobs for it once you have it
    • Right, so God, it's been nearly 12 months since my last confession....  The main confession is I'm a horrible car modifier (amongst other things).  Obviously the pool was a massive distraction for the entirety of last year but really doesn't excuse me for doing nothing at all on the car for this year.  To be honest this year was a mental break to get over the extreme mental torment and pressure I put myself through putting the pool in!  It really was a slog.  The pool is still not completely finished but it might never be....  The kids love it and the wifey and I love it so mission success! I have spent a grand total of 30 minutes working on the car since when I commenced on the pool.  I just have not had a spare brain cell to be able to focus on it.  The thought of working on it just seems abhorrent to be honest.  My heart is just not into it.  Yet..... What I have done is decide that I'm a clown to not paint ALL of the underside of the car while I'm at it.  Originally I was stopping at the start of the rear subframe to then "get back to it later on once I'm ready".  Let's be honest, later on might never happen so may as well keep diving in!  I'm already balls deep so may as well go a bit deeper! So......  I've just purchased a hydraulic scissor lift table to be able to take the rear subframe out as a whole unit without having to dick around with jack stands rolling around on the ground.  Us 6' 8" blokes don't operate well at ground level! One of these- Anyway, will the investment in an expensive tool that I'll probably only ever use for one job motivate me to crack on?  Only time will tell..... Wish me luck!
    • Yeah the ACL and similar formable heat shielding materials are really nice. But most people do not have the patience or talent to do a good job like that. Almost anything is better than nothing though. Even if you didn't form it closely like that and just had a slab of it slipped in between the manifold and somewhere/thing you wanted to protect, you would gain benefit. There has to be a market opportunity for people like Artec to make formed heatshields to suit their cast manifolds. The fact that they are cast means that they are consistently the exact same dimensions and they could add bosses to the castings like you see on stockers to allow heat shields to be firmly attached yet floating away from the manifold itself.
×
×
  • Create New...