Jump to content
SAU Community

Recommended Posts

im just looking at the workshop manuel now to see if they have a ign relay maybe lift the cover on the relay box and give them a wriggle or even swap some around and see if you get ign lights

I don't think so. the blue light still comes on on the remote when I press the buttons.

I'll probably wait until about 6-7ish and call a mobile auto electrician out and see if I can still make it to the show and shine depending on how early the auto electrician can get here/fix the problem.

Edited by Eddyfier

mate it depends on how it was fitted and what brand ect ect where they mounted the unit without knowing it's all guess work .

i dont think u can reset just a thought has the battery gone flat in ya remote at all?

is it a alarm and imobilser in one ? does the alarm have a key to turn it off under the bonnet ?a

Edited by mid life crisis
i thought the plan was to make it less obvious...?

I have highlighted the key word in your sentence there Dave :(

Nah that is still the plan, but since the rears rocked up I thought why the hell not? I went for a little slide drive with it like that but it was scraping on fking everything (understandably) so I took the lip off for now :D

that mean your back to nissan's andrew?

good to hear thought you were going a lil funny on us all with that toyota talk :(

take it you got yellow seat covers, almost looks like the person in the drivers seat has a mullet :D

Edited by Inline 6

^ thats my mum dude :(

I was going to let her drive it before I put the lip on, then I realised just how low it sat n thought the better of that idea :D

*edit* And nah I still don't really care for Nissans, I just reckon I've made this one look ghetto fabulous :D :D

s5003358trhrttz4.jpg

s5003362tt8.jpg

Edited by AndrewJZX100
good to hear thought you were going a lil funny on us all with that toyota talk :(

dont make me slap you datto boy.

speaking of, i just put an offer on one of those datsun geeteeaah's.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Dunno what to tell you, when I look at it on Consult I can see this warmup timing map kicking in around 40C coolant temp and it sticks around for a while:  At part throttle on the normal base timing map it peaks around ~43 degrees of timing or something like that, this warmup timing map drops it to like 12-15 degrees. 
    • I don't think that's what you're seeing. Something else doing that. The only time I've seen it get so retarded is when it's trying to control idle (in which case we're not talking about mapped timing tagets anyway) and when there is an extreme coolant temperature sensor fault. The RB26 ECU is essentially the same as the 20 ECU and I knew that ging inside out. There is no facility for it to retard that heavily on cold start. The OEMs never used to do it back then. I mean, shit, the catalyst is abotu 3 miles down the exhaust anyway. Early light-off was just a twinkle in some EPA arsehole's eye back then, not a regular engine control strategy.
    • I must preface my comments with a general expression of ignorance. I have no specific knowledge of these NA automtaic things. I can only assume that the "steering wheel button" is for enabling the tiptronic controls. Wierd that it would even need/want a button for that... But anyway.... Was the car previously tiptronic? Did you put a new cluster in as part of all this?
    • Regardless, it doesn't seem wise especially on RBs to actually chase MBT. Timing scatter is the big one on stock CAS, even if that's fixed overshoot is worse than undershoot. 
    • It's all about reducing the overall output. Reduce the source of it, you have wayyyy less to deal with in every other step and trick you play with. It's why something like a modern vehicle, so VW, Audi etc, there's thousands of tables for the ECU to calculate what it should be doing with the engine.   Why would you NOT reduce emissions the most effective way possible, when it has very minimal tradeoff, AND manufacturers are always struggling to meet the current standards.
×
×
  • Create New...