Jump to content
SAU Community

The Sa Wasteland


Cubes
 Share

Recommended Posts

cool, cheers steve. Hope i just need new spark plugs.

Have u got the steering wheel on yet?

Start with the plugs.

There is no benefit in going to Spitfire coil packs if your standard ones are OK - many claim the Nissan coil packs are better anyway, just way too expensive.

Make sure you clean the coil packs prior to re-installing, and you can use areldite (sp?) to fix some cracks.

Link to comment
Share on other sites

is it scandinavian flick entry commonly used in drifting?

yeah the drifters use it alot but i only use when the car is underpowered and can't spin the wheels with just the throttle! otherwise just use the handbrake

Link to comment
Share on other sites

call me stupid dave,

what what is your username derived from?

is it scandinavian flick entry commonly used in drifting?

or something far more complex that my not yet mature brain is in-capable of recognising?

dont worry craig, i recently owned up to dave that it only twigged to me recently what it meant.

only once i said it did it dawn on me :)

Link to comment
Share on other sites

drying your car is the most important part i have found... especially as i have a black car.

a good chamois and a microfibre cloth is what i use to get mine dry (i move it into the shed once i have washed her so the water does not evaporate)

Link to comment
Share on other sites

drying your car is the most important part i have found... especially as i have a black car.

a good chamois and a microfibre cloth is what i use to get mine dry (i move it into the shed once i have washed her so the water does not evaporate)

yeah , i might wash it and then roll it under cover and chamois it , dont have a microfibre cloth though :D

or i could use this waterless car wash i have , s**t's magical :)

Link to comment
Share on other sites

my housemates dog scratched my car :P

he is so bored (choc lab). we all play with him and walk him etc, but he still needs moar.

he tore apart a thing that had a massive piece of wire in it and it has whipped against the passenger side of the car *sigh*

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
 Share




  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...