Jump to content
SAU Community

The Sa Wasteland

Cubes

By Cubes,
in South Australia

 Share

Recommended Posts

  • Replies 36k
  • Created
  • Last Reply

Top Posters In This Topic

  • Damo_R34

    2820

  • scandyflick

    2266

  • Madaz

    1919

  • craig R33

    1717

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Ryanrb25
Ryanrb25

i went for a hills run last night in the 31 with the roads very slippery.....was much fun. Had to bed in the bottom end bearings so yea..took it for a strap.

DSTROY
DSTROY

Hey Ryan, do you know how to fit a set of drop spindles to the front of a hilux???

Madaz
Madaz

Dam straight Damo would rather do SAU them heroin gts4 are 4.1 because they share the same parts from the gtr i think r32 gtst is 4.3 because of the lack of torque from the rb20

Posted Images

RubyRS4 Grand Master

RubyRS4

Posted
Posted

Took a sickie today.

Didnt get up until 12 noon. Now I've been bored all day. :P

Would have been a great day to ride thru the hills ... but I'm too sick to ride :P

*flick* Veteran

*flick*

Posted
Posted

evening everyone.

So i did a good deed just now.. saw a dead cat on melbourne street n felt sad so i turned around and stopped and helped another lady drag it off the road.. poor kitty :P

Im a sucker for animals :P

Felt sad so decided to give my cat a hug when i got home, all i got was a scratch on the face and a hiss.

But yeh, theres my good deed for the week

jenkies Mentor

jenkies

Posted
Posted
um when i saw him run on the saturday he made 285 AWKW and 301 RWKW i doubt from one day to the next hes going to loose 30 awkw's :P

tiz true.. when my car ran on saturday they also diddnt put enough petty in.. had below 1/4.. might have something to do with it.. i dont know.. was workin sat :P but what i do have is the figures of previous tune results.. can scan in dyno sheets if need be. thanks for the comments and smiles bout engine.. yeh im pretty happy visually with it too...

chad, yeh just had to chuck the trophy in there.

post-27156-1224592648_thumb.jpg

Inline 6 Grand Master

Inline 6

Posted
Posted (edited)

G zilla back with mozilla :(

special thanks to dohmar for his pc skills

plug in for the man who don't like to self advertise;

for all your pc fixing needs contact dohmar :P dude hooked me a sweet custom made pc running a twin turbo nos setup to smoke any rival pc.

pm dohmar to get him to hook up your busted pc today :P if he's not too busy running up his credit card and changing the lights inside his dash to the 5th colour he's had

Edited by Inline 6
Damo_R34 Grand Master

Damo_R34

Posted
Posted
um when i saw him run on the saturday he made 285 AWKW and 301 RWKW i doubt from one day to the next hes going to loose 30 awkw's :blink:
tiz true..

:)

would look pretty defectable personally 18's are enough and once you go to a 19" tyres whoa mumma prepare to pay for rubber

Even the jump from 17" to 18" is a big jump in price unfortunately :P but yeah, i recommend 18"

CRoNic... Grand Master

CRoNic...

Posted
Posted
went and had my car remapped at turbo tune today and i gained 34 rwkw out of it

first run pulled 88.1 rwkw with a blocked fuel filter and fooked fuel pump..so replaced both of them and it pulled 111.2 rwkw

then after the remap it pulled 122.2rwkw..

im pretty happy with it considering the only mods are HD clutch, 2.5" full exhaust system with race cat and K&N panel filter

Ryder, hurry up and get a turbo!!

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • FRGTN1
      Fourth gear grind

      By FRGTN1 · Posted

      I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • RB2533
      UniClutch

      By RB2533 · Posted

      Yeah for sure that is peddle adjustment 
    • PotatoCake
      Attesa ETS Pro Install on R33 GTR

      By PotatoCake · Posted

      What are your thoughts on this after having it for a while, worth getting?
    • joshuaho96
      Fourth gear grind

      By joshuaho96 · Posted

      Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...