Jump to content
SAU Community

Recommended Posts

http://www.news.com.au/story/0,27574,26025279-421,00.html

if i was an olympian, i sure wouldnt f**k it up by being such a dickhead. it baffles the mind.

http://www.news.com.au/adelaidenow/story/0...5006301,00.html

they are human afterall :P

This follows another police officer being stood down after allegedly clocking 223km/h during an authorised pursuit. Read full report here

FAIL. Its called proof-reading.

mazda you queer, the only oldschool you should be aspiring to is the 240z :P

and should that not be posted in the awesome thread

240's can lick my swingers, waaay to expensive.

http://www.news.com.au/story/0,27574,26025279-421,00.html

if i was an olympian, i sure wouldnt f**k it up by being such a dickhead. it baffles the mind.

I guess when you haven't been an olympian for 13 years, you might get bored. :P

Thats hilarious Tangles! :banana:

LOL. :banana:

At first I thought it was a payout to me (picture of a blank slide) because of my extremely badly worded post above it. I meant Adelaidenow have 2 different reports on the same thing with 2 different crucial facts. :P

Have had a couple quick withdrawls from the Loxton SAU:SA display...

looking for people to fill between at least 2 places, if not 4

1-2 r33's

1-2 r34's

a kpcgr-10

an dr30 and or r31

an r35 gtr (i wish lol)

please pm me if you think you could be keen :domokun:

-D

The Stagea came off the road last night, for some much needed lovin'

Borrowed a timing light last night (thanks R334doors2) and decided to double check my timing this morning.

Problem: after removing the CAS, I noticed it was very 'tight' to spin, but however didn't make any worn bearing-type noises! I'm safely assuming this is not normal?

I have a spare CAS for RB, but it won't fit my Neo motor. This one spins much more freely, so my CAS is rooted. Clearly they're different, much to my inconvenience. :domokun:

post-48775-1252110766_thumb.jpg

post-48775-1252110920_thumb.jpg

Obviously, I'm in need of another CAS for RB25DET Neo? Will a non-turbo Neo be the same?

Help please! :banana:

So who are the softc0cks who said they would come to Loxton and are now pulling out? .... damn I hate how people always say they will come, then pull out .... why even bother saying you are coming if you are not going to go through with it? .... now it makes it much more expensive for each that are bothering coming to cover the associated hire costs ....

On that note Ben, I have a shelter that we used at Kadina - it is not flash, but is FREE. Happily hosted about 20 of us crammed in under it when it rained :domokun:

Big +repz to Classing Performance down at Hackham.

Took the GTR down there (managed to get it towed out by the RAA in the end), they showed me around the workshop, put the GTR on the hoist, explained a heap of stuff...

Awesome customer service. And the guys down there know their shit. Good to see they put in the effort to show you what they're doing to your car, etc. Most workshops just throw a invoice in your face.

Get the car back on Wednesday after 9 months of no action.

So who are the softc0cks who said they would come to Loxton and are now pulling out? .... damn I hate how people always say they will come, then pull out .... why even bother saying you are coming if you are not going to go through with it? .... now it makes it much more expensive for each that are bothering coming to cover the associated hire costs ....

On that note Ben, I have a shelter that we used at Kadina - it is not flash, but is FREE. Happily hosted about 20 of us crammed in under it when it rained :banana:

Got any pics of it dude? If it looks OK we can save ourselves $270 odd, otherwise we still have ample numbers to hire a tent if needs be

-D

EDIT - Any chance u can pursuede Munro to enter his 35? :domokun:

The Stagea came off the road last night, for some much needed lovin'

Borrowed a timing light last night (thanks R334doors2) and decided to double check my timing this morning.

Problem: after removing the CAS, I noticed it was very 'tight' to spin, but however didn't make any worn bearing-type noises! I'm safely assuming this is not normal?

I have a spare CAS for RB, but it won't fit my Neo motor. This one spins much more freely, so my CAS is rooted. Clearly they're different, much to my inconvenience. ;)

post-48775-1252110766_thumb.jpg

post-48775-1252110920_thumb.jpg

Obviously, I'm in need of another CAS for RB25DET Neo? Will a non-turbo Neo be the same?

Help please! :(

Yes a non turbo one will be the same.

With the one that you have taken off, being tight won't effect the performance of the CAS and apart from the bearings there are no touching parts in them, they are just a round disc with two sets of holes, one set has 360 holes and the other set has 6. Optics are used to gain the signal so apart from the bearings there isn't anything else touching.

who'da thought itd be so hard to sell a decent set of wheels.

been offered a bunch of trades despite me being fairly clear on not being interested in trades, and the trades ive been offered have been garbage.

sure, id love a set of super advans, but if theyre 7.5 and 8.5 wide with a +45 offset, why the hell would i want those? and the only cash offer that has been made has been for less than half the asking price. f**kin lowballers. im all for a bit of haggling, but knocking off close to 60% on your first offer? be serious.

/rant.

Edited by scandyflick

How do you remove the wires from the back of the cigarette lighter in a 33? I've unclipped every little tab on the stupid thing but the plugs still wont pull off and if i yank any harder the wire is going to break...

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • It only looks tidy, as most of the stuff that was on the whole back wall, is now in the trailer to go to the tip, or has been shoved in my 2.2x2.4m "Spare parts room", and now I can't get to anything in there Ha ha ha I could definitely do with a bit more space, but I'd just end up with your problems I'm going to enclose the car port beside the garage, and move a lot of stuff into it I think. OR... It will be setup as a fabrication area, and the main garage will have parts storage in it. I'm not sure yet... Need some pictures of that big shed you've got with the bikes and Skyline in
    • No. I think it's gone. 😭 I think you can get body coloured ones on eBay so I think I'll get one of those... Or just hang a red ribbon from the hole and whack a TOW sticker next to it.
    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
×
×
  • Create New...