Jump to content
SAU Community

Cheap Rb25 Conversion?

cherp

By cherp,
in Queensland

 Share

Recommended Posts

boot_it Enthusiast

boot_it

Posted
Posted
I dont think they are open anymore, or atleast not doing that well... I havent seen them down BWCP in about 18months either.

hey josh ttr are great company :closedeyes::spam: (joke)

remember when a certian person was telling u and your dad that it was fine to run a td06 on a rb25 with stock injectors and i said other wise and what happened to the motor after it ran down willowbank ?????

but meah sooo long ago and the memorys i have of that place

but to the guy that want to do this conversion theres plenty of sau members that will offer and hand to to the job some will offer great advice also if u want to learn about your car this is a great way to find out

666DAN Grand Master

666DAN

Posted
Posted
Can help with the wiring. I have done a few now. Excellent conversion, I even did one for my fathers R32 at the start of this year. He loves it!

I have personally done 2 now and have done them over a weekend with a hand from my bro-in-laws.

Cheers

I've heard nothing but good comments about this man, however make sure he leaves the brother-in-law at home :closedeyes:

blv Contributor

blv

Posted
Posted (edited)

i have done a few of these conversions now.

if your after a harness, give me the RB20 engine loom, and the RB25 loom and $350 and you'll have yourself a complete wiring loom that plugs stright on. if you have an R33 microtech, is it plug and play? If so, then as i stated above will be the way to go.

As for the motor, it will bolt stright onto your crossmember, however, as stated earlier in this thread, you will need a modified gearbox crossmember.

I can also do your tailshaft, as mentioned by showbag on the 1st page, i do tailshafts for a living, and trust me, you dont want to do any dodgey stuff in this department. I can build you a complete 1 piece tailshaft, brand new that will cop 350rwkw for $450. I use billet slip yoke and high tensile steel tube.

If you need intercooler pipe modification i can also help in this department, as with the exhaust, but the RB20 exhaust will bolt strauight up if both your RB20 and RB25 have standard turbos.

PM me if you need anymore info, i'll be glad to help.

Edited by blv

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I had absolutely no symptoms whatsoever that anything was wrong.... I'm very happy it was all spotto'd and re-bled and re-torqued and aligned though. Will be picking it up tomorrow and undoubtedly be like "Oh, that clunk is gone" "Oh, the car really wants to drive straight" "Oh, that pedal feels better" "Oh, it feels like I've gained 25hp" "Oh, the handbrake works now" It should have been a sign that the new Project Mu shoes had 3mm of pad depth on them out of the box, and the OEM ones from 25 years ago that we took out also had 3mm of pad depth, implying the issue was not, and never was the shoes, but we put that down to it not being adjusted correctly. It wasn't, but it wasn't even adjustable at all given one side was boned and the T Junction of the cables was on a 45 degree angle, the non-working side being the one on the massive angle. Obviously when I had adjusted it and reset it and re-tensioned it I had either got it stuck or something along those lines. Oh well. Live and learn and absolutely could have been catastrophically worse so I'm rationalizing it as a win, kinda. I also got the chance to measure the distance between rear rim and the suspension arm/shocks and found a 30mm rubber block only just doesn't fit there. Which is great to know before ordering wheels, when I assumed 30mm was easy. The man with the Porsche adapters has rims that use 23.9mm of that space, so it's safe to assume I have between 23.9 and 29.9mm of space there to play with on the inside. The wheels looked pretty stupidly pokey with the 20mm spacers on the rear, only for me to find that the studs come out another 12mm and the wheel doesn't actually sit flush with the hub because you're supposed to cut your original studs. The wheels do have cutouts that kinda accomodate it, but not fully. So my 20mm spacer was anywhere between 25mm and 35mm. ~25mm and send it will determine on where the wheels sit with the spacers on. When I put the pads in for the track day I will mess around with spacers (with wheels that do not clear studs properly when mounted to spacers) and do more math, for the last time, for the 7th time.
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Lucky pick up Best to find these things before something horrible happened to the yoke flange thingies I would hate to think what would happen if it dropped the tailshaft  Hopefully the holes are not flogged out in the yokes and it was just the bolts that got munted  As for the hand brake.....ouch, look like the disc got rather hot, and I assume smokey, I recall when I had a front caliper seize on the Commodore, there was lots of smoke and the disc was glowing cherry red when I was able to eventually stop and have a look, and stopping a big heavy car, going down a big hill with some rather high RPM down shifts and some hand brake action is something that makes you think hard about life
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      One of the things that never seemed right was the handbrake. Put in some nice new Project Mu shoes. We figured the rears were out, so why not. We're right there. My handbrake never worked well anyway. Well, this is them, 15km later. 67fdcf94-9763-4522-97a4-8f04b2ad0826.mp4 Keen eyes would note the difference in this picture too:   And this picture: Also, this was my Tailshaft bolts: 4ad3c7dd-51d0-4577-8e72-ba8bc82f6e87.mp4 It turns out my suspicions that one side of the handbrake cable was stretched all along were pretty accurate, as was my intuition that I didn't want to drop the tailshaft to swap them on jack stands and wasn't entirely sure about bolt torque. I have since bought the handbrake cables which have gone in. I'm very glad that I went to my mechanic friend who owns an alignment machine to get an alignment before the track day, because his eyes spotted these various levels of "WHAT THE f**k IS GOING ON HERE?". Turns out the alignment wasn't that bad, considering we changed the adjustable castor arms out for un-adjustable castor arms, and messed with the heights. Car drove pretty good with one side of the handbrake stuck on, unbleedable rear brakes, alignment screwy, and the tailshaft about to go flying and generally being a death trap waiting to happen! (I did have covid) (I maintain I adjusted the handbrake correctly, but movement caused shennanigans and/or I dislodged the spring on the problem side somewhat, or god knows what). G R E G G E D
    • 32.det
      My R32 Money Pit & The Headaches That Come With It

      By 32.det · Posted

      Very interesting, im not sure how all those complications fit in to running a haltech instead of a stock ecu but I'm starting to think I'm a bit out of my league.
    • GTSBoy
      My R32 Money Pit & The Headaches That Come With It

      By GTSBoy · Posted

      I just put 2 and 2 together. This is a Neo converted R32. The Neo ECU (in concert with the R34's AC controller) runs the AC quite differently to how the R32 ECU and AC controller do it. If you just drop it all in, it won't work. There is some tricky wiring required, including changing to the pressure switch that the Neo controllers want to see. I don't know what it is, because mine was done by a guru. It was a year or so after I did that transplant before he worked out what needed to be done.
×
×
  • Create New...