Jump to content
SAU Community

Recommended Posts

Ok so this is from my 260RS diff (LH Side). Does anyone recognise it from something else?

OutputFlange01.jpg

OutputFlange02.jpg

OutputFlange03.jpg

DIMENSIONS :

31.5mm diameter across splines

33mm diameter across middle section

35mm diameter across base of shaft

Spline section is about 40mm across the overall shaft length

31 teeth

155mm long overall

Does anyone by any chance have an R32 GTR or R33 GTR they can check?

It doesn't need to be the 6 x 1 flange as I'll change axles anyway. Basically I need to figure out the LH side so I can change both or find a RH side as I simply don't have it. This is so I can match the rear diff with the front 4.111

I am trying to avoid having to change my rear hubs to GTR

Thanks

Link to comment
https://www.sau.com.au/forums/topic/189737-260rs-diff-query/
Share on other sites

260RS diff is R33 GTR diff. So are the axles.

The only R33 GTR diff I had to compare against was an Active Differential type (which was definitely different) so you could well be right. To be honest I had always assumed that 260RS was R33 GTR but I suppose R32/R33 output flanges could be the same.

Ive smashed my front diff (rear is still good) so you might want to look at that too.

I'm already running the 260RS front diff, hence why I need to change the rear to match it.

R32 GTR output flange is close enough that I could probably use it. On a whim seeing as they are also R230 I tracked down some 300ZX TT output flanges to compare against, as you can see they're quite a bit different again

media1.jpg

Dammit. I meant to say output shafts the same, not the axle shafts... My bad, sorry.

Oh ok, so I need R33 GTR output flanges then, thanks for that ;)

EDIT : I can confirm that yes they have the same part number. Cheers Psy

On the subject of R33 GTR. Can I use this :

media1-1.jpg

Its an active differential. These apparently came out in some R33 GTS25T's aswell. Has anyone ever retro-fitted one of these to there Skyline/Cefiro etc. Can anyone forsee any problem?

Edited by tRUkbOY

Well I have it all sorted now, my R33 GTR RH Output flange is on its way from Japan.

On top of that I sorted my axles and I don't need to change my hubs to GTR/260RS spec either. In case your wondering, no I am not going to use my piddly RS-Four axles nor am I using axle/diff adapters.

It was (in the end) all very easy. If anyone is interested I'll update with photos when my Output flange arrives in 2 weeks.

you guys are crazy with your GTR setups

SIMPLE solution

S13/14/15/y33/y32/gtst/r32/r33/

all the diffs are interchangable

you might not have mounts for the attessa shit, but you can make them

I have an s13, with WGNC34 rear cover, s14 solid diff mounts, and Nismo 2 way

swap the input shaft for the driveshaft from teh C34 to the s13 diff, bolt that ish up

throw some greddy or veruspeed gear oil in there and your good to go guys.

just make sure you get the output shafts wit hhte same number of bolts (6 i think?)

you guys are crazy with your GTR setups

SIMPLE solution

S13/14/15/y33/y32/gtst/r32/r33/

all the diffs are interchangable

Yup, I know. I work for a Nissan dismantler :)

you might not have mounts for the attessa shit, but you can make them

I have an s13, with WGNC34 rear cover, s14 solid diff mounts, and Nismo 2 way

swap the input shaft for the driveshaft from teh C34 to the s13 diff, bolt that ish up

throw some greddy or veruspeed gear oil in there and your good to go guys.

just make sure you get the output shafts wit hhte same number of bolts (6 i think?)

Yeah but in the end it seemed crazy for me to buy another diff (I'd already bought 2 others) when I had 80% of a GTR diff already. The flange only cost me $300 & now it bolts straight in and includes the mount for the ATTESSA pump. The axles were easy (don't believe what people tell you) and I get to have a mechanical LSD as opposed to Viscous

Yup, I know. I work for a Nissan dismantler :)

Yeah but in the end it seemed crazy for me to buy another diff (I'd already bought 2 others) when I had 80% of a GTR diff already. The flange only cost me $300 & now it bolts straight in and includes the mount for the ATTESSA pump. The axles were easy (don't believe what people tell you) and I get to have a mechanical LSD as opposed to Viscous

So what is the final parts needed?

Diff?

Output shafts?

LH and RH axles?

Anything else?

So what is the final parts needed?

Diff?

Output shafts?

LH and RH axles?

Anything else?

For me personally? CV grease & LSD oil. Otherwise I'm not quite sure I understand the question Darrin...............

EDIT : Sorry, I just read further up the thread. I'm fitting it all on Saturday so provided I don't run into anymore issues I'll post the full diff swap with pics on Sunday

Edited by tRUkbOY

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...