Jump to content
SAU Community

Recommended Posts

Hey,

i'm just wondering if anyone has used the NGK Iridium Spark Plugs in their '33?

If you believe the brochure they're a lot better, but I've heard people say they're not worth the money - just wanting to know if anyone has had any experience with them or anythin similar - good or bad?

Thanks Guys!

Link to comment
https://www.sau.com.au/forums/topic/19013-worth-the-ngk-iridium-spark-plugs/
Share on other sites

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

Well my dad's GTR had problems with the platinum plugs fouling at anything over 1.2bar. we fitted the iridiums and they made a massive difference. much smoother and no probs at high boost. im going to get them for my GTS. i dont know if it would make a huge diff on a low powered car like mine. but it made a big difference with his.

Thanx for the speedy replies guys! does anyone know what the NGK platinums go for at say Autobarn/Repco? - don't wanna get ripped off!

also does anyone know the part number for these plugs for an R33 (NA)?

considering ive got an NA, what gap width would you reckon i should run them at?

Thanx for your help again

hey price is about $19.50ea

I dont know what u should gap them too. i know for turbo RB engines its 0.8mm but on the packet the iridiums say not to change the gap because the tips are very fine and fragile.

I gapped them to 0.8 anyway and they have been pretty good.

Yeah I know, a lot of things are overkill...but they spin a whole lot of crap about how much better the expensive stuff is, I guess people just believe them, a lot of us being those people!!! :P

I was quite happy to go with the cheap copper plugs until he explained to me why the Platinums were better...made sense to me so I bought them!

like i said earlier i have iridiums in mine at the moment. and im happy with them.

i paid $21 each i think, sure they spark stronger due to the finer tips. but i dont expect to see any big performance gain.

but the good thing is i wont have to change them for another 100K k's or so. (NGK quote 150K actually)

ron

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The max they would go for me is 50.
    • That cannot have been a fun set of drilling. The stock "baffle" looks identical to rb26, I just cut fuel cell foam to fit the full length under the baffle.
    • I understand your sarcastic exasperation. But to be fair - the baffles do indeed fit OEM cam covers. They did omit to say that you need to do a bunch of stuff. But they do fit them.
    • Got started on the modification to make these splash plates fit over the long weekend. First the surprisingly time consuming task of swapping all the cam cap bolts to Tomei cam cap studs. I did the method of removing one bolt at a time, applying loctite to the stud, double nutting to torque as the manual described. Then carefully unlocking the nuts without disrupting the torque of the stud (and going back to re-torque a few times when it slipped). Finally applying the nut and torquing to spec. Repeat x28 Next up I went about removing the stock cam cover baffle so I could ensure it was fully clean after drilling for stud clearance.  As the blind rivets holding the baffle on were domed I used a punch to mark the center then used 4mm drill bit to carefully drill out the rivet without going too far part the baffle. As seen in other thread here is what is inside the stock baffles I decided on M4x6mm bolts to bolt the baffle plate back on with. I used a 3.3mm drill bit with some tape to mark the depth at ~8mm. Next was to tap the threads using a cheap bunnings kit M4x0.7. With the baffle removed I also drilled out the spot welds holding in the baffle plate oil returns. Unsure whether this was the best option or if I should have cut holes in the Hypertune splash plates to allow the oil drains to still function... time will tell. I then removed the the Hypertune splash plates so I could rest the cam cover on top and use a dab of grease to mark where the studs impacted the oem cam cover baffle. The most obvious spot was on the hump from the stock mesh is held. Using this hole as an anchor I bolted the oem baffle plate back into the cam cover and lined up the Hypertune splash plate. Marked the rest of the holes for the studs and drill those out too. Total 32 holes drilled and 12 threads tapped on the passenger side cam cover alone for this bolt on part that totally clears all OEM cam covers.. Drivers side next as well as some E85 safe fuel foam to fill the space behind the behind cam cover baffle plates. oh and some lock nuts for the splash plates of course.
×
×
  • Create New...