Jump to content
SAU Community

Recommended Posts

This is what I will probably do on the next build, but as stated I have to stay to a buget, which unfortunatly is not 50K, wish I did have 50K, would have shopped around an bought an R34 GTR, theres an R34 NUR at J-Spec inports for 77k. I would snap that up if I had the cash! Had another go removing the turbos, almost there! Have decided to go the -5 and will have them soon.

  • Replies 79
  • Created
  • Last Reply

Top Posters In This Topic

Just picked up two brand new Garrett 2860R-5's today, should have the turbos off tomorrow and will be fitting everything this weekend. Fingers crossed! I need my car, its been SH#T driving my misses commo everywhere!

Turbos out!!! and thank bloody god for that, actually only took 2 hours with the help of a mate, found that not only was there a exhaust leak from the manifold (caused by two studs braking) but the rear turbo had blown out the gasket on the dump pipe. Anyway will be replacing all the studs (after I get the two broken ones out ) and also replacing all the gaskets and banjo bolt washers, will then transfer all the parts onto the new turbos and then fitting them. Now I have a quick question. The car currently is running a Blitz to atmosphere BOV, I want to replace this to a plumb back BOV, so whats a good BOV that will connect to the return piping?

Will post pics soon

Yes, but unfortunantly I dont have the stock BOV, when I bought the car it had been fitted with this Blitz to atmosphere BOV, however I have just purchased a brand new Trust Type R plumb back BOV with 2in connections. This will be easy to fit on my car with no modifications required, it is fully adjustable and should be suitable for any aplication I care to throw at it.

P.S: Got one of the broken studs out of the head today, now just one more to go!!, this ones being difficult though. Will try again tomorrow armed with some more tools! Once I have this out I will give the engine bay a clean and it will be ready to be put back together. Im hoping to get it back on the road in the next month.

Finally got the two broken studs out of the head, also removed the radiator today and sent it away to be flushed and cleaned properly. Ive bought all new hoses and gaskets, Im replacing all the studs with high tensile units including nuts. Some time this week I will be transfering all lines and dump pipes over to the new turbos, then they will be going on. Once this is done it will be a masive weight off my shoulders as this is prabably the biggest part of the job, next I will install the oil cooler and intercooler, and should be able to fire it up then! Still will be a couple of solid days work to get it there. Wish me luck, and that I dont run into any more problems!!!!

Yeah Ill try not to. Just bought a new genuine GTR badge for the rear, looks TOPS, when I bought the car I replaced the origional badge with an aftermarket one but it looked shit, the red was really off colour, this one cost $95 but looks great!!!! Now if I can only get the engine back together so I can drive the thing!!

  • 2 weeks later...

Hi all, the build has come to a hault for a while now, the car has been sitting in pieces while I decide what to do. I have been thinking about the oil problems associated with the RB26 motor, now assuming mine has stock oil pump and crank and being a 89 model and the fact that my bank account is low I am weighing up my options. To go the whole hog will cost upwards of $5k which I cannot afford right now. But what are your opinions on this setup, I am thinking about fitting a Tomei sump baffle kit, Jun crank collar, N1 oil pump, Tomei metal head gasket with restrictor plates fitted, while the head is off I will obviously send it away for a service and have the oil return galleries drilled. Now I have the N1 pump and can get the other parts from nengun for about $750 delivered. I am fitting a Trust oil cooler but will still be running the standard sump, with this fitted I would run the motor harder and be aiming for higher HP level but what are your opinions on reliability with this sort of setup? Also can anyone give me a rough price on what to expect to service the head and drill out the oil return galleries? Anyone know who can fit the Jun crank collar and can it be done with the crank fitted, I will have the motor out of the car if I do this as it will have to come out to do the sump baffle anway. I was going to leave this and address it later but it has been dragging on so I am thinking that while the car is off the road I might do the job properly, it will take me abit longer to finish as I will be spending money before I get it!!!! Bloddy car is sending me broke! I live in Sydney so need someone in Sydney to fit the collar.

If you're doing all that, you should consider putting in the extra money and adding forged pistons / rod bolts (and rods depending how much power you intend to make in the future, if sticking with 350kw @ 4 then standard rods are fine). At least that way you won't have to have it out again in a long time (assuming no problems). If you do that, you'll be able to run your desired power target for a long time with no issues... it's a big call though as it's quite a bit of extra coin... I'm sure you've considered this idea :)

Edited by TommO
  • 1 month later...

Its been a while since I have posted, the car is still off the road but I'm getting there, I'm also getting sick of catching the train to work because I have no bloody car!. Its been hard work But I am finally getting it together, I have fitted the turbos, exhaust, coolers and BOV, and it took alot of work with the grinder to get the cooler in! Now I just have to tighten up the manifolds and fit all the top piping and it should be right to start. I finally got my Power FC from Nungen, but I wont install it until I get the money together to get it tuned, samed with the 700cc injectors and boost controller. I should have it on the road on Sunday. Will let you know how it goes!

  • 4 weeks later...

Another lengthy "Mod'ing my BNR32" to XYZ RWHP" :(

My trick was...(to save myself ne ridicule) to never create the thread!!! :D almost 2 years off the road for me... serious.. back on the road in 2 months with 350rwkw's :)

Edited by GeeTR
hows the beast coming along pal....

Hi, the car is comming along fine, Its been back on the road for a little while now and everything seems to be working well, only problem is that the rear HICAS rack has started leaking so im thinking about replaceing it with a lock bar and getting rid of the HICAS al together. As for performance the car goes good with boost comming on early and heaps of mid range torque. But I havent had it tuned yet. I have all the parts to complete it but just need some time and I have to make sure I have the money to tune it before I finish. This left to go are: I have to fit the injectors, boost controler and Power FC. Once this is done I can get it tuned and it will be finished. Fitting of the parts isnt too much of a problem as I can do it myself but the tune will cost me about 1K, and I am spending all my money on my Karts at the moment, as the karting season is about to begin. It will be finished soon though, in terms of presentation it is pretty much complete and looks really good, Ill post some photos soon, Ive even had a few comments on the street, the other day I had some guy drive along beside me taking photos of the car! Then he gave me the thumbs up. Its been a long and tiring process but Im nearly there. I have een driving it nearly every day and it hasnt missed a beat so far, and it not even tuned. I am looking forward to feeling the end result when I burry the right foot though. The best thing about driving it untuned is that Im not thrashing it so Im getting almost good fuel economy :D . Anyway will post pics soon, and look forward to going on a SAU cruise when Im done. Keep in touch :P

  • 9 years later...

Hi everyone, back on here, I actually have another acount now but got access back to this one. I might pass this account into the new owner of this car. 

Mad an update on this car, it made just over 300awkw when tuned at CRD on 20psi but possible head float, so I ran it at 18psi and made, from memory about 290awkw. The thing was a jet, loved it, but it still needed more money, I got a quote to do a full proper build through CRD, but then got an offer on the car so decided to let it go. 

I know the new owner so I see the car regularly but it's been off the road for a long time now. 

New owner enjoyed it for awhile but then decided he wanted more power so gave me a call, we went down to CRD and booked the car in for a full build. 

Car got an r34 crank, nitto rods, pistons and oil pump, metal gasket kit, custom extended sump with baffles, head for light porting and full service with everything new including Tomei cams. All the bolt on parts remained, while the engine was out it was also fitted with a twin plate clutch. Motor is now bullet proof, 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Oh, that's grim. Something bad has been happening there.
    • Put an endoscope down the hole and saw this. Not quite all around the bore but a good 60% at least. Chin to the chest and towards further disappointments I guess.
    • 2 does "sort of" applies, maybe......but looking at what parts would be needed for the swap to get engineered, registered, and insured, and basically that's everything under the car, the modifications the make it legal would be problematic and horrendously expensive, all for a street car that just cruises around and hits a few twisty roads on the weekends Also, from looking at the NSW rules and Regs, with all modifications that is required just to make the car safe and not twist itself to pieces, and then actually get registered for street use, may still be impossible nowadays As for 1, when you add in a fresh engine, fresh transmission, rear cradle and diff, tailshaft, suspension, brakes, cooling, and all the other fabrication required, your probably looking at up to $100k to do it right, all for a 20 year old MX5 that is over engineered and you would never be able to actually use the power it has on the street, much like your beastie, which I love, but you actually track that thing and can use all of its powers in anger, in a safe environment  Hell, the old Bogan Cruise Ship had more power than I could use on the street, and in hindsight, I went a bit silly on that thing, it didn't really need the 500hp it had for what I actually used the car for, it was fun, but basically unusable on the street if you value your licence  As for cams, yeah, I'll probably book it in for them to get installed and tuned soonish, like next month after MX5 Mania are back at work....... and yes, I've already sent a email to bin the turbo quote and quote instead to install cams and a new Fluidampr balancer that will suit the 2.5 better than the OEM 2.0 balancer that is swapped over for the 2.5 install, as the balancer needs to get pulled to time the cams it's a while your in there sort of thing I did think a bit about flex fuel for a laugh, but being na, and no where really around locally anymore to get E85, I've binned that idea, so no sweet sweet corn smells are set for the car I wish E85 was more of a standard fuel, it's better for the environment, better for tuning, plus that sweet sweet smell we all love As for fitting in the family, that's not needed, as everyone in the family already owns a car that can seat 5 humans comfortably enough, the MX5 is "my toy" As for buying a car that is already built, nah, I would rather pick and choose my parts, I enjoy the process, and in the big picture, the additional cost is well worth the enjoyment, and the occasional frustration, I get out of doing it, albeit with other people spinning the spanners, and me, just paying the invoice 🤣
    • Excuse me, but 2) does apply 1) Would also apply if you consider how much is spent in the alternatives. Also there's the option of 3), buy one pre-built that you can put your family in (it's me, it's my car)   That said, I went on a ~500km drive the other day. I didn't use anything more adventurous than 3rd/4th gear at about ~3000RPM and 50% throttle and I was going as fast as anyone has any sense doing on a public road, with enough grip to the point where I didn't want to go any faster. I was obviously under the limit of the current car etc etc. MX5 with 2.5 N/A to achieve the same speed would be more fun for any road scenario. Maybe consider cams. I wouldn't boost it. The use case is just not there and it won't actually make the car more enjoyable unless you really do plan on wringing gears from 1st to 3rd (at least) at 100% WOT on a public road to 150+kmh.
    • Great if: 1. You had all of the money for everything else that is required  2. Lived in a country where you could actually do this and drive it legally on the road Sadly, neither applies to me As for the turbo, I am having second thoughts, mainly for engineering/registration legality reasons and insurance  Not saying I've finished doing stupid things that I probably should do to the MX5, but boost, and V8 engine swaps isn't on the cards Strange, but true 
×
×
  • Create New...