Jump to content
SAU Community

Gtr Vehicle Check

futurewa

By futurewa,
in South Australia

 Share

Recommended Posts

Deluxe Grand Master

Deluxe

Posted
Posted
I'm importing a GTR R32 from Adelaide to Perth and the vendor has had the car inspected at BOOSTWORX for me. Can anyone give me a heads up on this garage?

Majiority of the people on here will say Boostworx are great, Which they are!

Shaun and Troy are top lads, we also race with them, and are sponsored by them.......

Link to comment
Share on other sites
Adz2332 Grand Master

Adz2332

Posted
Posted
I'm importing a GTR R32 from Adelaide to Perth and the vendor has had the car inspected at BOOSTWORX for me. Can anyone give me a heads up on this garage?

Cant go wrong with them.. When i was looking at buying a 32 GTR i took it to them and they gave it the once over.. Was very detailed and gave a good inspection. Cant say enough good things about the guys down there.. And if anything they were a little over critical of the car which i would much prefer.

Link to comment
Share on other sites
Jase Collaborator

Jase

Posted
Posted
Dear? Compared to who till.....something i found him to be very reasonable

he does do good work no doubt and he is a good, knowledgable guy as well

I don't dispute that

he is just hard to pin down to a job price and hence I've spent a bit more than I expected a couple of times

Link to comment
Share on other sites
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • DraftySquash
      Newbie from VIC

      By DraftySquash · Posted

      Oh also, looks like it will be 3-4 weeks before they arrive - so no coolant change until then 😕
    • DraftySquash
      Newbie from VIC

      By DraftySquash · Posted

      @soviet_merlin Managed to find my part and get it off Amayama. While I was at it and paying 9.75 AUD shipping for a $1 piece, I thought I may as well get some other plastic clips I broke 🙈  Thanks a lot for this link
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      The point of all that for me was to get to the PDM (yes, v37 is as fancy as a haltech) which is between the battery and the front inner guard.  In there, pins 80 and 81 on connector E125 are for hi beam according to the USDM manuals. I chose to intercept the high beam signal there as it is next to the battery and firewall so it is a good place to mount the fuse/relay for the LEDs. Unfortunately because you can't access the PDM with the battery in the car, it is difficult to test those wires are correct. The fuses for Left and Right high beam are marked on the PDM cover, so I checked continuity from the fuses to those pins with a multimeter, and it seems to be right. From here I need to splice a wire into one of those 2, and run it into the cabin for a switch, then run the trigger wire back to that general location for the relay. So, I removed the driver's side guard liner to check out where the wiring leaves the engine bay and enters the cabin.  Turns out, that does not happen behind in guard liner at all....waste of time, nothing is routed through there, so that was another 5 pin clips, 4 screws and a bolt of wasted effort All of the wiring is actually run across the separate compartment between the engine bay and the cabin under the cowling...so off with the windscreen wipers after all....
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So....the good news is you don't have to remove the windscreen wipers to replace the 12v battery in a v37 (just). You do however have to remove: 1. Battery area cover (un clips) 2. Battery area trim (pin clips) 3. Nav side windscreen cowling (more pin clips, plus the trim between the cowling and the front guard, and half of the cowling to bonnet seal All of that gets you to here, with clear access to the battery While there, it is worth clearing out the leaves and dirt that run from the cowling into that well, my car had a lot of crap there and it is a guaranteed future rust hotspot
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Onto trickier matters....this time of year a LED light bar makes a massive difference to avoid skippies etc, so that was the first main priority. Unfortunately unlike both the Cima and the Fuga, there is no chance for a large central light bar inside the grille due to all of the redsport bits already there (intercooler radiator, extra water pump, sonar stuff). So this time I've gone a pair of 8" light bars which does have the benefit that they can be angled outwards a little as well. First, bumper needs to come off as there is no way to access the space behind the grill with it in place. Unlike the R32 which is (now) held on with 2 screws, the v37 had about 30 pin clips, 20 bolts and also 6 clips holding the damn thing on. Basically you remove the intake (clips), the top side covers (nasty clips) to get at 2 bolts, the front of the undertray (about 15 bolts and 3 clips), the front side inner guard covers (3 bolts and a couple of clips each) to get at the bolts at the rear of the bump in the wheel well, and then 3 clips near the headlight (outside, then under headlight, then above headlight) As part of that process the car got its first "race" mod so you can get at the top bumper bolts without removing the trim. There are also about 8 different electrical connectors which are in grave danger of being cut and replaced by one multi pin deutsch connector one day. On the bright side it is clear the bumper had never been off by how tight the connectors were. Once off, you can see there is very little space to work with. The lower section was not an option as the angle to the road would suck, plus the sonar module would push everything too far to the centre So I mounted the left side bracket to just clear the water pump (a miss is as good as a mile, they say) and the horn has been moved backwards too. The brackets on these Narva lights were a nice height to clear the front reo, and I just drilled and rivnut-ed into the reo (angle drills suck, but at least it made the job possible) With both mounted Minor adjustments to horn locations but everything else cleared. Those horns may well get moved / one deleted depending on how the cooling is on hot days, they were moved well to the side in the R32 Next, onto the wiring which will be a pain...
×
×
  • Create New...