Jump to content
SAU Community

NA to RB26DETT ??

NA_R33

By NA_R33,
in Engines & Forced Induction

 Share

Recommended Posts

NA_R33 Grand Master

NA_R33

Posted
Posted

Hi all,

Im planing to do this conversion around the middle of next year. But if funds permit i may do it a little earlier. Ill use the GTR rear dif and try get GTR brakes all round. My quetion is what box do u guys recomend as im not doing the AWD conversion i cant use the 6 speed box unfortunately :D How strong is the GTST box? as i want to do everything right the first time so when i have a bit more money down the track i can go for bigger power with fewer issues. Has neone done this conversion or have ne advice to give me it would be greatly appriciated.

Cheers

John

Link to comment
https://www.sau.com.au/forums/topic/19088-na-to-rb26dett/
Share on other sites
NA_R33 Grand Master

NA_R33

Posted
  • Author
Posted

haha yeah thats cool, i was always under the impression they were 6 speed?? oh well im not missing out on nething then, also a gtr half cut is around 6g's ive been told as a real approximate around 10g's give or take a few. but i will also need new wheels aswell, so im giving myself a 15g limit for when i do it so i should be able to do a few mods straight away aswell. from my current insurace policy they only quoted 160 bucks extra for the conversion, and im 17 rating 5!!! i made the mistake of not getting it in writing cause im sure id never get a quote like that again it must have been a mistake.

Link to comment
https://www.sau.com.au/forums/topic/19088-na-to-rb26dett/#findComment-401751
Share on other sites
NA_R33 Grand Master

NA_R33

Posted
  • Author
Posted

i saved since i was like 10, working at my grandfathers company, then when i was old enough i worked at maccas aswell, i started saving for a car before i even knew what a skyline was, i managed to put together 10g's and my parents gave me another 6. and by the middle of last year i was a very proud owner of a skyline, since then every dollar i have earnt has gone into my car. And after y12 im planning to take out a 15g loan and do the converion.

Link to comment
https://www.sau.com.au/forums/topic/19088-na-to-rb26dett/#findComment-401828
Share on other sites
Greg Veteran

Greg

Posted
Posted

this might be a stupid question but why are you getting the extractors if you're doing the conversion next year? i hope you go ahead with the conversion, it would be good to see it done and that way i'll know exactly what needs upgrading so I can do it to my car once i finish uni :D

what age do you get your license in queensland? i get mine in less than 3 weeks!!

Link to comment
https://www.sau.com.au/forums/topic/19088-na-to-rb26dett/#findComment-402044
Share on other sites
NA_R33 Grand Master

NA_R33

Posted
  • Author
Posted

u get ur learners when ur 16 and 6 months and have that for 6 months then u get ur p's then stay on them for 4 years. Yeah i figured the extractors wearnt too pricey and i just wanted i little bit more performance from my car for now, the high flow insert also isnt too pricey and an apexi afc i can use with the new engine.

Link to comment
https://www.sau.com.au/forums/topic/19088-na-to-rb26dett/#findComment-402060
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...