Jump to content
SAU Community

Recommended Posts

Hi, I am new to the forum and would like to know if anyone has destroyed their turbo on a Skyline? I have read a lot about not putting the boost over 12psi, but I am wondering if anyone has done this and caused damage, or whether it is just a myth. I know there has to be a limit at some point, is it 12psi or are there people out there running their stock R33 turbos at 14psi or higher?

What are your stories of disaster.

Link to comment
https://www.sau.com.au/forums/topic/19118-have-you-destroyed-a-turbo/
Share on other sites

Mine was running at 13psi quite happily turbo wise, although it was starting to ping a bit too much so had to wind it back to 12psi.

12psi I'd say is perfectly safe as long as you have a good tune and decent FMIC. My high boost has been that or 9 months or so with no adverse effects and some pretty hard driving occasionally. Depends whether its a series 1 or series 2 turbo.

As mine is a daily driver i often just run stock boost to and from places, so i wouldn't say i run 12psi all the time. People will also argue whether 10-11psi is more optimal in terms of overall performance too.

I have a R33 Series 1 and have been running 14psi for around 2 1/2 years now. The only problem I have had is the turbo sucked in and ate the rubber bung that the car yard put on to block the Bov return hose when fitting the atmo venting BOV. The same turbo is still on and going strong.

The previous owner of my car destroyed the stock turbo doing 15psi on his daily commutes to brisbane...tortured, replaced, and hi-flowed it in the end...saved me some big money :)

It runs 10psi now for daily driving, but can go up to 18psi, no sweat. Right now, that figure is a little too far fetched though

Skylines have been found by a lot of people to make better, more 'useable' power on around 10-12psi. Note 'useable'... No point running more boost if it aint doing much or downgrading performance and reliability. The fact of the matter is if you are going to boost, you need to mod and free up the airflow so that it is actually worth boosting in the first place. You'll find obviously that if you run a stock skyline on say 12psi, then have another with a cooler, exhaust, filter and tuned on 8 psi it will run a heap better and harder than the 12psi stocky. Boost does not just = power.

R33's really need an aftermarket ECU to take advantage or should I say unlock some decent power.

200rwkw isn't bad considering its a stock turbo.

The FMIC and ECU make a big difference to the R33's.

R32's pitty its not the same for the R32's. :)

Over 10-12psi the stock ECU starts doing strange power dip things.

I aren't running a computer now with my big turbo, cooler, exhaust blah blah and it still runs pretty damn well considering, however am expected to pick up around 25rwkw from computer they reckon, so on about 15psi tuned they said i can look at around 235-240rwkw which aint too bad :) But yes they do need a computer to run well, without one they jsut eat fuel and run very rich. Not good on the wallet believe me ha ha.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • yeah i agree paint match stops it from standing out so much, oh that's actually really good to know i was wondering if it would help with air flow now actually having an outlet in the bonnet. Will have to focus on ducting into and out of the radiator now to make the most of it.
    • I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
×
×
  • Create New...