Jump to content
SAU Community

Stcok Standard R32gtr


locoloc
 Share

Recommended Posts

I just brought a stock standard r32 gtr. (and I mean stock standard )

I'm not sure how powerfull or restrictive they are with the stock parts, but I swear I felt a

lot more kick in my old car ( old car = r32 gtst, fmic, exhaust, r33 turbo, hks opod filter )

Does this sound right??

I do feel that there is power, but I dont feel much pull. I heard that a stock gtr is supposed to be quick.

In first gear it lags unitl about 3000 rpm, then a small kick, then at about 5000rpm it kind of levels out

The revs continue to climb but only at a steady pace.

The same thing happens in second.

By third gear it feels quick but thats because it's already been an eternity and i'm already going over 1ookm.

The engine sounds fine but just sounds lioke it's working very hard after 5000rpm for not much gain.

ALL I'M REALLY CONCERNED ABOUT IS THAT HAVE I BLOWN A TURBO(S) OR IS THE STOCK SET UP VERY RESTRICTIVE.

It doesnt bother me if it's not quick, but I just need to know if it's as quick as it can be for the current set up.

Does anyone have any insight.

Link to comment
Share on other sites

First thing you should be checking is smoke pouring out your exhaust if a blown turbo is suspected to be the culprit.

I cant comment much on the gtr stock as a rock performance, but as far as I am aware they are referred to as very quick stock, but referring to stock as upgraded exhaust, filters, boost etc. Thats when they crack the 12sec barriers.

How much power was the R32gtst putting out? Id assume around 185-190rwkw. That is still fairly quick in the lighter r32, probaly a mid to low 13sec car.

It is an interesting comparison.

Link to comment
Share on other sites

Also it depends on your drivnig style. As we all know not everyone likes to be launching there r32gtst with the weak gearbox, so you may have adapted a similar driving style with the GTR. Go to the drags, rev it to 6000rpm, side step the clutch (if it can handle the power?) and im sure you will then witness what the GTR is all about.

I'd be interested to know what others think.

Link to comment
Share on other sites

Also it depends on your drivnig style. As we all know not everyone likes to be launching there r32gtst with the weak gearbox, so you may have adapted a similar driving style with the GTR. Go to the drags, rev it to 6000rpm, side step the clutch (if it can handle the power?) and im sure you will then witness what the GTR is all about.

I'd be interested to know what others think.

thats a fair comment...

Becuase the engine sounds and feels fine, or very good.

And there feels to be a lot of potential with minor mods...but I thought I would feel a lot more torque with a stock set up, thats all.

Link to comment
Share on other sites

You felt a 'kick' from the R32 as you had a turbo that was a tad laggy.

So it ramped up onto boost differently.

The GTR is stock, whilst they are not slow in stock form, they arent exactly a rocketship either.

I suggest taking the car to a performance mechanic and have them inspect the car if you are unsure of it.

Link to comment
Share on other sites

You felt a 'kick' from the R32 as you had a turbo that was a tad laggy.

So it ramped up onto boost differently.

The GTR is stock, whilst they are not slow in stock form, they arent exactly a rocketship either.

I suggest taking the car to a performance mechanic and have them inspect the car if you are unsure of it.

Agreed any car with stock boost generally delivers power in a very linear fashion.

Dont take it out and thrash it, if there is a problem you will only make it worse- get it checked out by someone that knows gtr's and can check the tune as in the AFR's.

at least then you can drive your new car knowing its all good.

Link to comment
Share on other sites

If you are worried I would suggest the following:

First up, check the timing. Insufficient ignition advance will make the car feel sluggish.

If that is ok then take it to a dyno & get it run up. Check the AFR's while you are there.

Then you will know for sure.

What you need to remember is that you very quickly get used to how "fast" a car feels - particularly a turbo car as it lacks immediate torque. As often as not a car with a flat torque curve will feel slower than one with an uneven one. Despite the first of the two being quicker.

Link to comment
Share on other sites

just dyno it....

correct me if im wrong but stock gtr will only put out 185kw...

A dead stock GTR with pods & cat back is about 210rwkw.

210rwkw pulling 1530kg is feels like puss.

... Time for mods locoloc :P

Link to comment
Share on other sites

Wait I know a guy with a r32 gtr with only pod filters (that he knows of) and it made 228rwkw not awkw. and runs like high 8's down an 8th mile (200m) the dyno may have been a little high maybe but it does pull away from my 200rwkw r33

Edited by RPR33
Link to comment
Share on other sites

dude if it flatens out at 5k check your running 20deg of timing, some people 'tune' them to run on 'aussie fuel' aka 91oct and run them at like 10deg of timing to stop any chance of pinging. that would make it feel like it goes ok when the turbos come on boost then die in the ass just after.

Link to comment
Share on other sites

thanks for all inputs...

I hope it is a timing issue and I also suspect it to be a fuel issue.

I dont want to touch the timing as I dont really know what i'm doing...

Gonna book in for a dyno and get the timing looked at

Once again, It doesnt bother me if it's not zippy because I intended on slowly building it up anyway.

At the time of purchase I had a workshop check it. compression test it and they also sais the car drove well..

The compression was (i cant remember exact) around 160 with only 5 psi diffence between all cylinders..

The only faults they could point were some minor leaks in the engine which should have been fixed for the RWC..

It's just disappointing because I thought I had something I could start fresh on....

However all may just be well,, wait till the dyno results and someone a bit more GTR knowledge to look at it.

Link to comment
Share on other sites

Sounds dirty! I mean you should check the AFM's/AAC valve/intercooler/throttle body etc etc. because they all affect boost response and A/F ratios.

I'm no expert but common sense is you should do basic maintenance like that (esp. on an old car) before checking for turbo wear or anything else more serious.

The GTR should be zippy. You shouldn't have a doubt that its quick!

Link to comment
Share on other sites

The only stock standard GTR I went in was really really disappointing. Was running stock boost, stock exhaust, stock everything - I struggled to believe it.... I had a semi-wanked up NA Honda which was pretty comparable in acceleration (dodges flames).

The new owner of the otherwise mint R32 GTR trucked on and did a full service, got it a very unrestrictive full exhaust system, pod filters and an electronic boost controller for it and ran 1bar of boost. He was pretty happy with it and told me I should come for a drive to see if I thought it was better - to be fair I didn't have overly high expectations after how horrid it felt before. Seriously, the thing lost traction when it hit full boost in first and had my whole hearted attention from that point forward. It felt like it was designed to be like that... like Nissan would have liked to have done it from factory but knew they shouldn't, so set it up so you really HAD TO.

Edited by Lithium
Link to comment
Share on other sites

Yeah, when first got my car I got bored of the stock power very quickly, leaving me with the same questions as you. If it was really meant to be like that, or if my car had some problem.

Turned out to be coming on boost rather late compared to a friend's GTR. After a thorough inspection, it turned out that the turbo fins were kinda chipped and worn, but still functional.

A change of turbos, ecu, ebc, etc. and with a much lighter wallet, I got a 135rwkw gain at the time, without any extra lag :blink:

When it was stock it was dynoed at 165rwkw :P

Needless to say, I was stoked with 300rwkw, too bad that feeling of contentment didnt last long, or else I would be a much richer person now :blink:

Edited by Yawn
Link to comment
Share on other sites

Turned out to be coming on boost rather late compared to a friend's GTR. After a thorough inspection, it turned out that the turbo fins were kinda chipped and worn, but still functional.

How did you find that out? Removed the piping around the turbo's? Cause i'm experiencing boost loss, wanna fix it asap!

Link to comment
Share on other sites

Basically my mechanics singled that out as the problem from their past experiences and after checking everything else. I didn't actually take anything out to confirm that was definitely the problem.

So i just assumed that was the problem and starting planning for turbo upgrades. Only when the stockies finally came out did I find that out for sure.

But in saying that, I was going to change turbos anyway, so I didn't want to spend unnecessary money just to check if the fins were screwed and then putting everything back on.

Link to comment
Share on other sites

Personally i think its suffering from stock car syndrome.

I drove an r33 gtr earlier this year and i found it very slow. I remember mentioning to Lithium on the net later that i was very dissapointed. My s14 was much faster simply due to the weight difference which i think is your problem here also.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • People still have Skylines? I thought they're non-existent now. 
    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
×
×
  • Create New...