Jump to content
SAU Community

Recommended Posts

Hey all just popping in real quickly again to ask the opinions of the forum. Car is a 95 gts-t with fmic, pod with cai, 3.5" turbo back exhaust split dump, running 12 psi with an ebc, always run 100 ron fuel, plugs gapped at .6 or .7, stock everything else and afc neo. Now I was watching my afr's the other day at full throttle and without a tune on stock ecu the reading I got was never below 11 is that common for a skyline with these few mods? Now I'm thinking the readings are definately off cause while at idle I never get anything below 16 just want to confirm that the wideband is stuffed, when at full throttle I never get anything below 11 and I had the wideband exposed to exhaust fumes and heat for like a week before I got power to it. All help is appreciated and welcomed. Thanks again in advance. Also a friend of mine has a ca18 that he wanted to get 300 - 350 rear wheel hp out of and I was wondering if you guys could help out or point in the right direction car is virtually stock and its an automatic.

Link to comment
https://www.sau.com.au/forums/topic/192302-is-this-heard-of/
Share on other sites

it cant hurt to get your readings checked against a calibrated 5 gas analyser.

Also those WB02 sensors are very sensitive to exhaust leaks.

Unless your exhaust sytem is 100% sealed then your readings are worthless

I think all skylines with stock ecu's do it once you add boost, thats why so many people get s-afc's to get that extra power, mine runs down to 10.5ish on full throttle!! although I haven't run it again after putting in a new 02 sensor. but I wouldn't stress about it mate >_<

  R31Nismoid said:
Silly question here.. is the AFC actually tuned?

A tune of the AFC would resolve this... being thats what they are used for

Nismoid thats why I am asking the question, not silly at all ,I'm thinking its a bit high for an untuned skyline on stock ecu.With the mods I listed thats a whole lot more breathing room for the engine so I was expecting 10's at least, another mod I forgot to mention is a bosch 040 fuel pump recently installed like 3 months back, also fpr with gauge and stock pressure reads 44 psi at idle without vacuum. At idle also the widebands reads and shows nothing less than 16 and goes all the way to lean as the car warms and in closed loop mode still nothing less than 16 just was wondering if this is common or can I say the wideband is stuffed come on you don't find this a bit strange. Now i can't say my exhaust is perfect but there are no leaks I can visible hear or see.

I think a few people have missed the point. The 02 sensor should be keeping the AFR at ~14.7 in closed loop as Fat is saying. Usually it would be a bit richer at full throttle also.

Most likely either:

1. Stuffed measurement device (AFRs its reading are wrong)

2. Stuffed fuel pump

3. Stuffed Fuel pressure regulator (check fuel pressure at rail at idle)

4. Stuffed O2 sensor (Doesn't explain only 11:1 AFR at full throttle - usually would be richer)

4. Stuffed AFM (less likely)

Edited by benl1981

if you want good ratios, you need a tune.

02 sensor has little to do with it most of the time. thats why some people run it without that feedback. also the ratios depicted may be inacurate depending on where the wideband is installed in the exhaust and the piping size. any leaks (which many cars have) makes it even more "guessy"

11s is not that rich anyway

That's what he's saying - he expected it to be running richer than that. Mine was in the 9-10s when I upped the boost which is usually how they go.

O2 sensor is what sets the AFRs at light load and idle. In fact I can drive around town in closed loop most of the time if I baby it round. The tune has to be close to the mark first but then the 02 sensor will bring it back to 14.7 AFR by playing with the injector duty cycle.

Take it to a dyno and pay $50 to get it checked there both on idle and full throttle, then if its the measurement device you havent wasted your time trying to fix a problem that isnt there.

Edited by benl1981
  benl1981 said:
I think a few people have missed the point. The 02 sensor should be keeping the AFR at ~14.7 in closed loop as Fat is saying. Usually it would be a bit richer at full throttle also.

Most likely either:

1. Stuffed measurement device (AFRs its reading are wrong): Really think so either the wideband O2 is stuffed or there is a leak in the exhaust cause I did all the test on the device to troubleshoot it and everything was spot on

2. Stuffed fuel pump: Brand new bosch 040

3. Stuffed Fuel pressure regulator (check fuel pressure at rail at idle):44psi

4. Stuffed O2 sensor (Doesn't explain only 11:1 AFR at full throttle - usually would be richer): Maybe read that if you have them connected without power to it might stuff it up and i did for like a week thats the wideband tho have a narrowband on the way that I will install ths week

4. Stuffed AFM (less likely): Could be but doubt it

  benl1981 said:
That's what he's saying - he expected it to be running richer than that. Mine was in the 9-10s when I upped the boost which is usually how they go.

O2 sensor is what sets the AFRs at light load and idle. In fact I can drive around town in closed loop most of the time if I baby it round. The tune has to be close to the mark first but then the 02 sensor will bring it back to 14.7 AFR by playing with the injector duty cycle.

Take it to a dyno and pay $50 to get it checked there both on idle and full throttle, then if its the measurement device you havent wasted your time trying to fix a problem that isnt there.

:Wish I could but dynos are rare over here would fix a whole lot of shit but have to wait a month before they bring the dyno back!!! :rolleyes: You all know how it is once you get someting you want it perfect right away just don't have the tools man so I gatta eliminate stuff on my own really think its a leak tho with the seal around the gaskets of the decat pipe might be my mind but think I can hear a little air escaping will get that siliconed also the dump pipe area and move the wideband O2 sensor to just before the deact pipe tis weekend and see if that fixes it.
  rollin_on_18_strong said:
it cant hurt to get your readings checked against a calibrated 5 gas analyser.

Also those WB02 sensors are very sensitive to exhaust leaks.

Unless your exhaust sytem is 100% sealed then your readings are worthless

Hey Thanks all found the prob as you stated they are very sensitive to exhaust leaks. There is a hole the size of my finger right above the wideband O2 sensor bung half assed welder didn't weld it properly. Gonna get it welded shut on the weekend hopefully this person does a better job and I can finally tune the car properly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...