Jump to content
SAU Community

Recommended Posts

Hi all,

I am having big over boost issues with my KKR 480.

If I disconnect my actuator so the waste gate is fully open the car still hits about 25psi at 5000rpm :S...

The turbo is fairly new and the wastegate isn't getting stuck closed.

It makes no sence... you shouldn't really see any boost when the wastegate is fully open.

I had this same turbo on my VS commodore and that didn't over boost.

First time I boosted it with the KKR480 in it I saw my AutoMeter boost gauge hit the stopper so about 35-40psi and it blew one of my silicone joiners inside out when I ripped my foot off the accelerator and this is running with the actuator hocked up with no boost controller.

Edited by Finny
Link to comment
https://www.sau.com.au/forums/topic/192546-stopping-overboost-with-iw/
Share on other sites

either the internal wastegate is too small, or your exhaust is too free flowing.

perhaps try a restrictor in your exhaust first, and if that fails, look at an external wastegate setup.

Yes my exhaust is very free flowing, Also jeff please read the tread before replying.

Problem is I want a low mount manifold because I just got my dump pipe and intercooler piping fabricated to suit the low mount but I am pritty sure there is no low mount external gate manifolds about.

I had the same problem as you man, turned out the dump pipe i had on my stock turbo wasn't the right size for the new turbo and the wastegate flap would hit the inside of the dump pipe when it opened and blocked it off. This ment that it would overboost something crazy just like you said. I ended up getting the wastegate pipe enlarged so the flap could fully open.

Disconnect your actuator and then open the flap and listen if it hits the dump pipe before it is all the way open.

Actually scratch what i just said above!

My car is still doing it!!! Went for a spin then with the actuator disconnected and still hits around 20psi!!

I had the dump pipe fixed the other day and the wastegate doesn't hit on it anymore so i thought it was sweet but after going for a test then its still doing it.

Looks like im still in the same boat as you buddy. So does anyone know what F***ing causes this??

Is it that the split dump pipe can't flow enough gases through the 1.5" wastegate pipe or what?

Dude KKR480s have a dump molded into the turbo so that its just got a V clamp back end. It is impossible to modify.

I got my waste gate bored out about 5mm all the way around so from about 20mm to 30mm and it made no difference, still boost spiking like crazy with the waste gate fully open.

Hmmm well i guess in your situation the dump pipe isn't the cause of it. I reckon in my case its the turbulance in the split dump in the place where it joins is that its not flowing into it and causing back pressure through the wastegate. This means that the exhaust gases go the path of least resistance through the turbine housing.

I might try to get an all in one dump pipe with no split, or just make mine into a screamer, which i dont really want to do....

I had this problem when i started tuning my ecu.

With the stock ignition map, the ignition is so retarded that boost is uncontrollable.

I fixed my ignition map and it was sweet.

Could it make it overboost that high from just the standard map :)

I have done some pritty mad tuning with my SAFC II so that this thing spools at 3000rpm I might disable my changes and see how it goes.

I also have maximum timing and a strait through 3" exhaust with a cannon, no mufflers.

I bored the wastegate out my self... but because I didn't replace the flap I bored it out about 1-0.5mm less than the size of the flap which is still a huge difference. I will bore it out further and change the flap and see how I go but I dont think its going to make any difference because the V clamp dump is too restrictive for a larger wastegate hole.

I really don't know why people say that the KKR 480 is a laggy turbo, my car is pritty much stock and it spools it before 3000rpm.

so can having a car running too rich and retarded make it overboost

Ive never heard of this before

It may be the answer to my problem

mine doesnt overboost by too much i can still rev to around 6000 rpm before it boost cuts

Yeah i've never heard of it either Pedro, doesn't really make sense how a car running on a rich and retarded map would somehow cause the exhaust gases to go through the turbine instead of going through the wastegate. At the end of the day exhaust gases are just basic fluid mechanics, go through the path of least resistance, usually being the wastegate when it's open. So to me, any major overboost problem is caused by the wastegate pipe no longer being the path of least resistance, wether it's caused by turbulance or something else?

Has anyone had a major overboost problem, not talking about 1-2psi and found a way to fix it??

This is from http://www.sdsefi.com/

"In severe cases of retarded timing, the mixture is still burning when the exhaust valve opens. Because turbochargers are driven by the energy in the exhaust stream, high EGTs caused by retarded timing produce so much energy at the turbine that even a fully open wastegate cannot control the boost pressure. All in all, retarded timing is counterproductive to producing an efficient, durable, powerful engine."

So at the retarded map with a very free exhaust the wastegate cant flow enough. I had 20psi with stock maps and went down to 7psi with a advanced ignition map. nothing else was changed

If you did have a larger wastegate that would solve the overboost problem as would having more exhaust back pressure.

I had this problem when i started tuning my ecu.

With the stock ignition map, the ignition is so retarded that boost is uncontrollable.

I fixed my ignition map and it was sweet.

how did you do it? (ignition map) manuali? or i can fix it by AFC NEO ?? ( i have afc neo) an if by afc neo what settings you did?

Na factory ecu tuning. the last load pont of the rb25det map for ignition is super retarded. If your hitting that point it would cause problems. I was hitting it on the rb25det ecu with a straight pipe and a intercooler.

Its just R and R which everyone goes on about.

Dont have a clue how to tune an afc.

If you bring down the afm voltage you could read of a lower load point i surpose?

Edited by srf

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jap premium will be 100 RON. You should use 98.
    • The exhaust gases are at their highest temperature as they leave the exhaust port and enter the manifold. They cool as they flow through the manifold because they transfer heat to the manifold and the manifold loses heat to the surrounding environment. Thus, inevitably, the exhaust gases are cooler as they enter the turbo compared to when they entered the exhaust manifold. So, yes, the exhaust manifold can easily get as hot as the turbine housing. Having said that, you will generally see the highest temperatures where the exhaust gases have to slow down or they are concentrated into one area - which is usually the collector on the manifold and in the turbine housing, because the gases slam into the metal at those places, increasing the convective heat transfer coefficient and transferring even more heat to the metal than they might just flowing past elsewhere. Exhaust manifold heat shields are a good idea - certainly for the stock manifold they are there from the factory. People seldom have anything like that on a tubular manifold because they are hard to achieve. Some might wrap a tube manifold with fibreglass tape - but this has a reputation of leading to cracked welds. The best case is generally to put ceramic coating onto the manifold to prevent it getting as hot (internal coating) and radiating/convecting heat into the bay (external coating). All the real heat from a turbo comes from the exhaust side. The gases entering are at ~800-900°C and the steel/iron gets nearly that hot. The compressor side is only going to heat the charge air up to <<200°C (typically not much more than 100°C). So that's nothing, by comparison. The compressor is not a significant source of engine bay heat.
    • Late to the party, specifically joined this forum as I just bought one of these and this thread has been a gold mine of info. If the OP is still around, mind if I ask what gas you been putting in yours? Mine has a Japanese sticker in the cap saying premium but it seems to get way worse mileage on premium (95) than 91. I always thought it was meant to be the other way round🤷 I do think Nissans claimed "6l/100km" is a bit fantastical 😂
    • Does exhaust manifold get hot as turno exhuast side? I have a turbo cover to managr heat in the engine bay but  nothing is covering the exhaust manifold before turbo   i know as turbo does compress air, the temp does go up however does that mean exhaust manifold would be as hot?
    • It's excellent but I'm still breaking it in so I'm not 100% sure where it'll end up. I would say it's about 15% heavier than stock and the smoothness of the slip zone is quite progressive but you need to be a little patient compared to stock or it'll bite hard and stall. Stock I got away with absolutely horrid clutch control. Like I said before I couldn't even tell where the clutch would grab when it was stock so releasing way too quickly without enough revs it would just slip and the revs would drop lower than ideal but that would be the end of it. Currently there's a bit of a nasty clutch judder if I don't apply enough revs + find the exact wrong point of the slip point in the clutch pedal but it feels like it's slowly resolving as I drive it more. I would not recommend the competition clutch unless you really need the extra clamp force. I think this clutch combined with the Nismo operating cylinder is going to be exactly what I want. Enough bite that you need to remember the release point to avoid stalling or rough shifts, but progressive enough that it's not hard to drive by any means and not heavy at all. I tried a "super single" clutch on my friend's 997.2 Turbo 6MT and that was absolutely horrid. It runs an electrohydraulic power steering pump for the clutch power boost so there's zero feedback in the clutch pedal and there was a horrific clutch shudder well after break-in due to the lack of marcel springs or hub springs in the friction disk. It felt like the slip zone was the thickness of a single toe twitch as well so it was almost impossible to avoid stalling it unless you gave it a ton of revs and just dumped the clutch instead of trying to be smooth with it. I was terrified of pulling out in front of traffic. I have also tried some kind of "super single" on an EK9 and that makes this twin plate Coppermix look like a stock clutch. Releasing the clutch pedal even slightly too quickly feels like you're getting rear-ended. The pedal is extremely heavy as well and there's no vacuum assist like the GTR.
×
×
  • Create New...