Jump to content
SAU Community

Recommended Posts

hey team sau

i have a genuine nissan skyline sign for an r33 that has the light in it to light up "SKYLINE" in green.

I took it out of my r33 a few years ago and i'm installing it into another. only problem is... the 2 wires coming out of it are both white... exactly the same... no black mark to show negative

halp!

Link to comment
https://www.sau.com.au/forums/topic/193694-skyline-rear-light-up-wiring-issues/
Share on other sites

It might not matter the slightest which way around they go? Like a light bulb.. it can go in 2 ways and still work.

PS. Never seen the wiring or inside of these rear lights before :wave:

EDIT: PPS. Just plug it in you pussy :)

Edited by SKY RYAN

Yeah, more then likely it wont matter... I don't know how it lights up exactly... but if they are diodes of any sort, then it only works one way, and unless you put a SHIT LOAD of current through it (enough to melt metal wire), then you wont do any damage to it...

Grab a pic maybe...

or just HTFU and plug it in :wave:

Yeah i doubt it will matter what way the wires go, just try it and if it dosnt work try it the other way. If that dosnt work either then maybe you have blown it up and shouldnt have played with the wires lol

Nah it will be fine just test it on another wire lol

EL lighting typically has an inverter somewhere around (probably in the panel itself) and it'll probably have reverse current protection as well.

Stock wise, they're wired to the parkers (mine just has the usual spliced connection into the rear park lights).

I've seen people make LED fittings up to change the light colour, however it's fairly fiddly to do as there isn't much room for a diffuser.

The EL panel is a solid panel covering the entire logo, when they work right there isn't any uneven parts to the light from them, however sections wear out over time. With LEDs, you'll have "hotspots" of light right where the LED is, and unless you can get the light to diffuse right, you'll get dark spots as well.

All this said, you can change the colour, it just takes a bit to get it to look even.

I've seen people make LED fittings up to change the light colour, however it's fairly fiddly to do as there isn't much room for a diffuser.

The EL panel is a solid panel covering the entire logo, when they work right there isn't any uneven parts to the light from them, however sections wear out over time. With LEDs, you'll have "hotspots" of light right where the LED is, and unless you can get the light to diffuse right, you'll get dark spots as well.

All this said, you can change the colour, it just takes a bit to get it to look even.

I wont bother then. I know i will probably screw it up.

  • 2 years later...
woudnt u get defected for having that light lit up on da back?

Wowwww raised from the dead don't you think? But his is a factory option so no, and most cops don't care as long as it's not too distracting

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
    • Nah, not really responsible for that little fiasco, but I'm still pissed at myself for writing off my 86, or when I reversed my VX into a pole just before selling it, but, meh, 5hit happens to stuff, all it takes is a slight distraction, and life is full of distractions, and "dooh" moments   
×
×
  • Create New...