Jump to content
SAU Community

I Need An Led Tail Light

Span

By Span,
in Tasmania

 Share

Recommended Posts

Span Enthusiast

Span

Posted
Posted

Hi!

I am afta a functional LED light for my 1995 R33. it has a curvy spoiler instead of a square one and my LED light is muffed so need a new one. if anyone has one i would love to buy it providing it works ofcourse.

THX

Span

Link to comment
https://www.sau.com.au/forums/topic/195339-i-need-an-led-tail-light/
Share on other sites
Span Enthusiast

Span

Posted
  • Author
Posted
if it's to suit the series 1 style i have one forsale.

cool! well im not sure if it would fit mine because mine is a series 1.5... it has the curvy rear spoiler. heres a picture of the spoiler below... if you think its the one i am up for buying. How much would you be asking?

Dan

post-40730-1196166104_thumb.jpg

Span Enthusiast

Span

Posted
  • Author
Posted
yup, it's the same as mine. $45 including postage?

its all good man. i am getting one from jds on thursday when my car goes in to be looked at. sorry to stuff u around. thx tho.

peace

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...