Jump to content
SAU Community

Highflowed Rb25/vg30 Bb Turbo

NYTSKY
 Share

Recommended Posts

NYTSKY Grand Master

NYTSKY

Posted
Posted

Hi all,

When i get my car back next month i will be pulling the turbo off and will be sold,along with braided oil and water lines.

I purchased an 0P6 housing and had it matched with my turbo.Then it was highflowed at Precision Turbos.

Highflow consists of machined front and rear housings(maximum)

Garrett Ball bearing cartridge.(will try and find the serial number for the cartridge)

It also comes with braided oil and water lines.

It has only been on the car for roughly 7000kms and is basically brand new.

I made 250.9rwkw at 16psi with this turbo.Has alot more in it and wouldnt be suprised if it would make 270-280 with a bit more boost.

The rear housing cost me $350

Braided lines $200

Highflowing of turbo $1550

Im asking $1650+post firm.

Old turbo off new turbo on.... big power!

NOW WITH FREE SILICONE INLET PIPE(second hand in excellent condition)

Bass Junky type.

Contact by PM.

CHEERS

post-32255-1197418639_thumb.jpg

post-32255-1197418705_thumb.jpg

post-32255-1197418769_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/197284-highflowed-rb25vg30-bb-turbo/
Share on other sites
  • 1 month later...
NYTSKY Grand Master

NYTSKY

Posted
  • Author
Posted

OK everyone i have finally got my car back so the turbo will be coming off the car.Those who sent me PMs for the turbo please get in contact with me before it goes to someone else.

NYTSKY Grand Master

NYTSKY

Posted
  • Author
Posted
dyno chart?

comes with reciepts/warranty?

direct bolt on for r33 gtst s1?

reason for selling?

Doesnt come with a warranty.But the thing is in great condition,i wouldnt be selling it if it wasnt.

Reason for selling is i have another turbo waiting to go in.And it will bolt on no probs comes with braided lines as described in first post.

stolen_s15 Mentor

stolen_s15

Posted
Posted
is the just a standard r33 highflow? fitted it yet?

Sure is mate. Would have loved to buy NYTSKY's turbo its a very well spec'd hiflow but mine was too much of a good deal to pass up.

Its getting tuned today, I'll post up the results tonight after I've taken it for a drive.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • pogman
      George's R33 GTST build

      By pogman · Posted

      yeah i agree paint match stops it from standing out so much, oh that's actually really good to know i was wondering if it would help with air flow now actually having an outlet in the bonnet. Will have to focus on ducting into and out of the radiator now to make the most of it.
    • The Bogan
      George's R33 GTST build

      By The Bogan · Posted

      I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • shortyboy
      Drive By Wire Conversion options

      By shortyboy · Posted

      Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • pogman
      George's R33 GTST build

      By pogman · Posted

      small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
×
×
  • Create New...