Jump to content
SAU Community

Recommended Posts

Hey,

Trying to find a R33 GTR to buy but cant find one in sa that apeals to me... but in queensland there is one that looks like what im after, even down to the colour and price (shit body kit on it tho!! lol)... Its just what has to be done to get rego on it here in SA? does it have to go through a full regency inspection?

The mods are

Garrett 400HP Turbo GT2860R x 2.

Sard 650CC injectors,

high volume Nismo Fuel Pump,

CES Ceramic coated dump pipes and secondary exhaust

80mm system with high flow CAT

Apexi Power FC with Hand Controller,

NI Water Pump.

Tomei Poncams Type "B" and Tomei adjustable timing gears

clear timing gear cover,

GFB Bleed Valve,

Tein Super Street fully adjustable suspension with EDC controller for on the move electronic adjustment.

So the defectable things would be the turbos, Apexi power fc, tein suspension... that all?

Id have top change that to get redgo?

Link to comment
https://www.sau.com.au/forums/topic/197949-buying-interstate/
Share on other sites

Have bought a few cars including my GTR interstate.... you must take it for an identity check only. (check vin/engine no to see if stolen)

Go to sturt inspection depot... will be easier than regency.

However if they see any obvious major defect they will send you to regency for full inspection.

Have bought a few cars including my GTR interstate.... you must take it for an identity check only. (check vin/engine no to see if stolen)

Go to sturt inspection depot... will be easier than regency.

However if they see any obvious major defect they will send you to regency for full inspection.

so i dont even need to take it to regency?

when you say major defects, on that list is that just suspension and if i disconnect the power fc handcontrol that would be ok?

apart from that?

Going to the sturt shop is the same as going through the engine check section at regency. All the do is check the vehicle complies with the import thingo (plate) and the engine numbers match etc.

If u do get defected (when i should say) u will need to take off the AM parts anyway-

Garrett 400HP Turbo GT2860R x 2. - come off

Sard 650CC injectors, - come off

high volume Nismo Fuel Pump, -ok (IF its internally mounted)

CES Ceramic coated dump pipes and secondary exhaust - ok

80mm system with high flow CAT - ok (providing its less than the required Db)

Apexi Power FC with Hand Controller, - out (der)

NI Water Pump.- ok

Tomei Poncams Type "B" and Tomei adjustable timing gears - ok (as long as the cam gears are covered)

clear timing gear cover, -covers the last point ie get rid of it if u dont want an instant defect regardless...

GFB Bleed Valve, - off (its altering boost)

Tein Super Street fully adjustable suspension with EDC controller for on the move electronic adjustment. - off

Basically they frown on anything that isnt std. So if yer buying the car fer all the bits, and end up taking them off later, is it worth the extra?

They can be engineered, but it will cost, and once again regency can say no they dont like it anyway (law unto themselves) and dont have to comply with any engineers report.

Edited by Bl4cK32
Going to the sturt shop is the same as going through the engine check section at regency. All the do is check the vehicle complies with the import thingo (plate) and the engine numbers match etc.

If u do get defected (when i should say) u will need to take off the AM parts anyway-

Garrett 400HP Turbo GT2860R x 2. - come off

Sard 650CC injectors, - come off

high volume Nismo Fuel Pump, -ok (IF its internally mounted)

CES Ceramic coated dump pipes and secondary exhaust - ok

80mm system with high flow CAT - ok (providing its less than the required Db)

Apexi Power FC with Hand Controller, - out (der)

NI Water Pump.- ok

Tomei Poncams Type "B" and Tomei adjustable timing gears - ok (as long as the cam gears are covered)

clear timing gear cover, -covers the last point ie get rid of it if u dont want an instant defect regardless...

GFB Bleed Valve, - off (its altering boost)

Tein Super Street fully adjustable suspension with EDC controller for on the move electronic adjustment. - off

Basically they frown on anything that isnt std. So if yer buying the car fer all the bits, and end up taking them off later, is it worth the extra?

They can be engineered, but it will cost, and once again regency can say no they dont like it anyway (law unto themselves) and dont have to comply with any engineers report.

OK thanks for that.....

But what would be needed to be removed for the very first check to get redgo here?

anything that is an obvious defect...Nothing that would make them considering calling u back >_<

Probably just keep the sus jacked up, swap the clear cover, and try hide the turbos under some heat shield and u should be in and out.

cheers for the advice!

wish it wasnt in Queensland!!! id be driving if it was in melb!

Have bought a few cars including my GTR interstate.... you must take it for an identity check only. (check vin/engine no to see if stolen)

Go to sturt inspection depot... will be easier than regency.

However if they see any obvious major defect they will send you to regency for full inspection.

CORRECT..........and the things that stand out the most are black windows, too loud and too low.....other than that make sure your pods are secured because they sometimes shake them.

my dear Adam

why dont u try to get a stock 33 GTR

at least u know it hasn't been thrashed

go through Regency, then mod what u want... the right way

IMO

honestly for 2 reasons.

1 stock can still be thrashed!

2 cheaper to buy one with things done to it already then out lay yourself and its easier to do it that way

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
    • Probably a smart choice to buy one vs build, purely for the motivation part as you said! Imagine the metal dust everywhere from grinding all the steel to build one. Ha ha ha!   Also, post a photo of your garage.   Mine is below, this is where I've been cleaning and have already half filled a caged 6*4 trailer. And this is after my cleaning expedition mentioned previously... The middle normally has a car in it, but I'm dumping things in the middle as I sort through them. And poor skyline was dusty and has had the lightest few drops of rain and now it looks atrocious and needs to be dragged back out and washed thoroughly! And yes to the right is technically another bay, you really can only see 2 bays out of 3 in this picture.  
    • It's more like on average the things I see a lot of things going wrong. Yes, usually the people who reach out are the ones who are having problems but on average it feels like mechanics and tuners here aren't really competent. I swing between thinking my standards are just way too high and wondering whether people really are just this dumb. I just had the strangest 10+ reply argument on a Facebook group over someone insisting that the factory R34 GTT boost control solenoid reduces boost pressure to 5 psi when it's on and raises boost pressure to 7 psi when it's off despite showing the exact plumbing in the factory service manual and the solenoid behavior detailed in the FSM.
×
×
  • Create New...